《耐高温辐照交联阻燃聚烯烃》由会员分享，可在线阅读，更多相关《耐高温辐照交联阻燃聚烯烃（4页珍藏版）》请在金锄头文库上搜索。
1、 耐高温辐照交联阻燃聚烯烃电缆料 High temperature resistive, irradiation cross-linked, flame retardant POE compound 1、 产品型号、用途 、 Type and application 牌号 Type 名 称 Product 用途及电缆规范 Application and Cable Specification FJZ1125H 125辐照交联阻燃聚烯烃电缆料 125 Irradiation cross-linked, flame retardant POE compound 交联仪器、仪表、电机引出线，通过 U
2、L3271 标准，符合 RoHsUsed for cross-linked wires of apparatus and instruments, electric motor and etc. Pass UL3271 standard. Meeting RoHs standard FJZ2125H 125辐照交联阻燃聚烯烃电缆料 125 Irradiation cross-linked, flame retardant POE compound 交联仪器、仪表 ,灯具线等，符合 RoHs Used for cross-linked wires of apparatus and instrum
3、ents, lamps and lanterns and etc. Meeting RoHs standard FJZ1135H 135辐照交联阻燃聚烯烃电缆料 135 Irradiation cross-linked, flame retardant POE compound 交联仪器、仪表、设备绝缘电线电缆，符合 RoHs Used for cross-linked and insulating wires and cables of apparatus and instruments, equipments and etc. Meeting RoHs standard FJZ1150H
4、150辐照交联阻燃聚烯烃电缆料 150 Irradiation cross-linked, flame retardant POE compound 同上通过 UL1581 中的 38 类标准，符合 RoHs Same above, and pass the 38 grade standard of UL1581. Meeting RoHs standard 2、产品性能 电线电缆用辐照交联聚烯烃是以聚烯烃高分子树脂为基料，加入特殊稳定剂、阻燃剂、改性剂、交联剂等其他特殊助剂，经特殊工艺加工而制得的粒状料。 、 Irradiation cross-linked POE compound, ba
5、sed on POE resin, is produced and pelletized by special technology with adding special stabilizing agent, modifier, flame retardant, cross-linking agent and other special additives. 3、加工工艺 采用一般挤出机加工，普通 PVC 螺杆 L/D 20，低压缩比挤出模头，要求低拉伸比。 、 Processing The compound can be processed with conventional extrud
6、ers, and the screw with a minimum 20:1 L/D and low compression ratio die is recommended. Low tensile ratio is needed. 推荐挤出机各区点设定温度如下： The following temperature( ) profile of extruder is recommended: 区点 Zone 1 区 Zone 1 2 区 Zone 2 3 区 Zone 3 4 区 Zone 4 机头 Head 模头 Die 温度 temperature 140 145 150 155 150
7、 150 4、储存与运输 包装： 25kg 一袋，聚乙烯薄膜内袋，牛皮纸复合袋外包装。 运输与储存：电缆料在运输过程中不应受日晒雨淋，应储存在清洁、阴凉、干燥、通风的仓库内。 、 Storage and transport Packaging： 25kg/bag， PE membrane inside bag and Kraft outside bag. Storage and transport: Avoiding in direct sunlight and weathering. The storage place should be in clean, cool, dry, and v
8、entilated conditions. 5、辐照剂量 辐照交联阻燃聚烯烃电缆料的辐照剂量建议为 15 兆拉德。 、 Irradiated dosage The normal irradiated dosage（ recommended） of irradiation cross-linked and flame retardant POE compound is 15 megarad. 6、产品性能 (见表 ) 、 Properties 表 Table FJZ1125H FJZ2125H FJZ1135H FJZ1150H 试验项目 Item 单位 Unit 标准值 Standard 典型
9、值Typical标准值Standard典型值Typical标准值Standard典型值 Typical 标准值 Standard 典型值Typical比重 Density g/cm3- 1.34 - 1.30 - 1.33 - 1.32 硬度 Hardness Shore - 91 - 95 - 92 - 92 拉伸强度 Tensile Strength MPa 12.5 14.0 12.5 16.0 12.5 15.0 13.8 16.0 断裂伸长率 Elongation at Break % 200 350 200 360 200 380 300 400 冲击脆化温度 Impact Bri
10、ttleness Temperature -25 通过 Pass -25 通过 Pass -25 通过 Pass -25 通过 Pass 20体积电阻率 Volume Resistivity,at 20 m 1.010122.010131.010123.010131.010122.010131.010123.01013介电强度 Dielectric Strength MV/m 20 24 20 25 25 25 25 25 氧指数 Oxygen Index 30 30 27 28 27 27 27 27 热延伸 Thermal Prolongation 负载下伸长率 Elongation Un
11、der Load % 100 20 100 25 100 25 100 25 冷却后永久伸长率 Permanent Elongation aftercooling % 10 0 10 5 10 5 10 0 空气热老化 Thermal Aging 热老化温度 Aging Temperature 1582 1582 1582 1582 1652 1652 1802 1802热老化时间 Aging Time h 168 168 168 168 168 168 168 168 抗拉强度变化率 Variation on Tensile Strength % 80 103 80 102 80 107 80 110 断裂伸长率变化率 Variation onElongation at Break % 80 98 80 97 80 90 80 86 以上数据为交联后的性能指标。 The above data are all the properties of compound after cross-linked.
