《(2020年)企业采购管理最全的外贸采购条款》由会员分享,可在线阅读,更多相关《(2020年)企业采购管理最全的外贸采购条款(62页珍藏版)》请在金锄头文库上搜索。
1、- 页面 1- SKF General Conditions of Purchase 斯凯孚采购一般条款 Valid from 2008-05-21 自2008年5月21 日起生效 These conditions of purchase shall apply in full unless otherwise agreed in writing. Any other general conditions shall not be applicable, even if they were not rejected explicitly in any individual case. 除另有书
2、面约定,本采购一般条款应当全部适用。任何其他一般条款不应适用,即使其在任何个别情况下 未被明示拒绝。 1. Definitions 1. 定义 1.1 ”SKF” shall mean any company within the SKF Group of companies purchasing products under these General Conditions. 1.1 “斯凯孚”应指在本一般条款下采购产品的斯凯孚集团内的任何公司。 1.2 ”Supplier” shall mean any company delivering products to SKF under th
3、ese General Conditions. 1.2 “供应商”应指在本一般条款下交付产品给斯凯孚的任何公司。 1.3 ”Agreement” shall mean any agreement between SKF and the Supplier related to the sale and purchase of any products. These General Conditions and the SKF Quality Standards for Suppliers (as defined below) form an integral part of the Agreem
4、ent. 1.3 “协议”应指斯凯孚与供应商之间有关销售及采购产品的任何协议。本一般条款及斯凯孚对供应商质 量标准(定义如下)是协议的有效组成部分。 1.4 ”Products” shall mean any products and services purchased by SKF under these General Conditions. 1.4 “产品”应指斯凯孚在本一般条款下购买的任何产品及服务。 1.5 ”Defective Products” shall mean Products that are not in accordance with technical and o
5、ther specifications specified or otherwise established by SKF or are not fit for the purpose intended. In the absence of documented SKF requirements, ”Defective Products” shall mean Products that are not in accordance with approved sample deliveries of the Products or where no samples are delivered,
6、 do not conform to generally accepted industry standards. 1.5 “瑕疵产品”应指不符合斯凯孚指定的或另行建立的技术规格及其它规格的产品或不符合特定用途的 产品。如无成文的斯凯孚要求,“瑕疵产品”应指与经批准的产品的交付样品不符之产品,或在无样品交 付的情况下,与普遍接受的行业标准不符之产品。 1.6 ”SKF Quality Standard for Suppliers” shall mean quality requirements issued by SKF Group Purchasing. 1.6 “斯凯孚对供应商质量标准“应
7、指斯凯孚集团采购部出具的质量要求。 2. Inspection of production 2. 产品检验 2.1 SKF shall have the right to inspect the Suppliers production, take samples and carry out other necessary investigations on the Suppliers premises. 2.1 斯凯孚有权对供应商生产进行检查、采样并在供应商场所采取其他必要检查。 2.2 It is the Suppliers responsibility to see to it that
8、 SKF can exert its right according to clause 2.1 even in cases where production is assigned, partially or entirely, to another - 页面 2-company. 2.2 供应商有义务负责使斯凯孚有权根据第2.1条行使权利,即使部分或全部生产委托另一公司进行。 3. Quality, Ethical and Environmental, Health & Safety requirements 3. 质量、操守、环境、健康及安全要求 3.1 The Supplier sha
9、ll comply with the SKF Quality Standards for Suppliers, which implies adoption of the principles of the SKF Code of Conduct and of SKFs Environmental, Health & Safety (EHS) Policy (http:/) and shall ensure that any Sub-Contractor approved by SKF under Clause 6 of these General Conditions, is legally
10、 bound to a similar compliance obligation. The Products shall be in accordance with technical and other specifications specified or otherwise established by SKF. All specifications will be considered to require that each Product must be new when delivered to SKF, unless the applicable specifications
11、 expressly permit the delivery of used, reconditioned or remanufactured Product. SKF may refuse to accept any Products that do not conform to all applicable specifications, in which case the Products will not be considered to have been delivered by the Supplier. 3.1供应商应当遵守斯凯孚对供应商质量标准,该标准包含对斯凯孚行为准则、斯
12、凯孚环境、健康及安全 政策原则 (http:/) 的采纳及应确保任何斯凯孚在本一般条款第6条下批准的分包供应商 受相似遵守义务的法律约束。产品应当与斯凯孚指定的或另行建立的技术规格及其它规格一致。全部规格 将被考虑以要求每一产品交付给斯凯孚时必须是全新的,除非可适用的规格明确允许被使用过的经修理的 或经改造的产品。斯凯孚可拒绝接受任何与全部可适用的规格不相符的产品,在此等情形下,视为供应商 未交付产品。 3.2 After SKF has approved sample deliveries and respective specifications, if so provided, of t
13、he Products, the Supplier is not allowed to change the function, appearance, properties, material, or place of production of the Products, without the prior written consent of SKF. 3.2 斯凯孚批准产品的交付样品及相关规格后(如有提供),未经斯凯孚事先书面同意,供应商不得更改 产品的功能、外观、属性及材料。 3.3 SKFs approval of Products shall not affect the Sup
14、pliers liability under the Agreement. 3.3 斯凯孚批准产品并不影响供应商在协议下的责任。 3.4 The Supplier shall notify SKF forthwith of any known or apprehended Defective Products. SKF shall notify the Supplier of any Defective Products within 6 months after the Defective Products have been detected by SKF. 3.4 供应商应当立即通知斯凯孚任何已知或察觉到的瑕疵产品。斯凯孚应当于发现瑕疵产品之日起六个月 内通知供应商。 3.5 If, on account of Defective Products, SKF deems it necessary to carry out an inspection of any or all Products delivered, this shall be effectuated, after consultation with the Supplier, at the Suppliers expense. The Supplier shall