《G040_123伺服阀检测仪说明书》由会员分享，可在线阅读，更多相关《G040_123伺服阀检测仪说明书（22页珍藏版）》请在金锄头文库上搜索。
1、APPLICATION NOTESVALVE CHECKERG040-123伺服阀检测仪说明书型号G040-123翻译：许国超本文件供参考2010年6月CONTENTS 目录Chapter Title Page 扉页1. Description 3 产品描述 3 2. Specification 7 规格说明3. Quick Start 9 快开4. Connecting to valve and plant 11 阀的设备连接5. Plant mode operation (in line) 12 工作模式操作（在线）6. Checker mode operation (stand alon
2、e) 15 检测模式操作（离线独立）7. External 24V supply 17 外部供电24V8. Valve performance checks 18 阀性能检测9. Block diagram 20 流程图DESCRIPTION 产品描述1.1 The Moog G040-123 Valve Checker is an instrument capable of checking theflow control function of nearly the complete range of Moog electrical feedback(efb) proportional a
3、nd servo valves. Mechanical feedback (mfb) and pressurecontrol valves are not catered for by the G040-123. 穆格 G040-123型伺服阀监测仪是一种能对穆格阀就近能对阀的流量控制，比例阀和伺服阀电气信号反馈检测的仪器。带机械反馈的压力控制阀不能用G040-123型检测仪。The feature that makes it so versatile is the way it can test a valve while thevalve is still installed in its
4、 normal operating plant. This is done at two levels,“in line” and “stand alone”. 这种仪器特点能对安装在阀台上正常工作的阀门进行多方面的检测和操作。这里有两种测试方式：在线检测和独立检测。1.1.1 Plant (In Line) 工厂工作（在线检测）As in fig a) the plant and valve operate normally. In fig b) the Valve Checker isconnected between the plant electronics and the valve
5、 such that all the plantelectronics signals, to and from the valve, are connected as normal. The ValveChecker monitors the plant electronics signals and the signals back from thevalve, enabling a check of the valves performance. 图a为电气线路与控制阀通常连接方式； 图b为伺服阀检测仪串联在电气线路和控制阀总电气线路之间，保证阀输出输入线路在正常状态。检测仪器能检测电气
6、信号和输入给阀信号，来检测阀的性能。1.1.2 Checker (Stand Alone) 检测模式（独立检测）In this mode the plant command is switched out while the Valve Checkergenerates the command to the valve and monitors the signals back from it. Thevalve remains installed in the plant but the plant command signals aredisconnected. Checking whil
7、e still installed in the plant provides the addedbenefit of checking the valve by observing the reaction of the plant to the ValveCheckers commands.在这个模式下操作，工厂工作指令被断开，检测仪的控制信号输给阀，阀的反馈信号在回到检测仪。尽管检测仪还串联在电路中，但工作的信号已经被断开。检测的同时，可以由检测员给出指令来监测被测阀的动态变化。1.2 The Valve Checker is powered by the plant electroni
8、cs which also continue tosupply the valve in both plant and checker modes of operation. As well, thereis a +24V DC power connector on the front panel for 24V DC and 15V DCpowered valves, without connection to the plant electronics power.1.2检测仪的供电源由原电路供给，同时能继续提供给被检测的阀在“ 工作”和“ 检测”模式操作提供电源。同样这里的24V直流电源
9、可以提供阀电子元件所需的24V直流电源或 15V 直流电源。无须外接其它的电器电源。1.3 Two cables connect the Valve Checker to the plant electronics and valve. Each of the Valve Checker models is dedicated to a power supply voltage andconnector type. It is necessary to select the model type that has the correctconnector and supply voltage.
10、 The table below shows the model numbers andtheir supply/connector types.1.3连接在检测仪的两条电气线一条接供给的电线，另一条接被检测阀的上。不论检测仪那个模式下都是这样连接来提供电源电压和连接方式（接头一般类型一样），对于必须要选择类型的要纠正连接类型和提供的电源电压。下表提供的是型号和电源电压参数Model dash number table:零件模块参数表 Model dash 型号 connector 接头、插接件 supply 供给1.4 There are six functional blocks on t
11、he front panel.在面板上有六个的功能模块1. Q Command 电流指令 4. Control 控制2. Spool 滑阀 5. Enable 开启，允许3. Power 电源 6. Valve Connector 阀连接接口1.4.1 Q Command 电流指令This block is active only when checker mode is selected. The rotary pot adjuststhe Q command level.只有在选在“检测模式”下这部分模块才能投入使用，旋转钮是调整电流的大小量的。The grey test point gi
12、ves a 0 to 10V signal proportional to the actual voltage orcurrent being delivered to the valve. The rotary selector switch selects thesignal type that is connected to the valve.这个灰色的测电位点提供0V10V成比例的输出真是电信号，信号主动传递给被检测的阀件，旋转的扶手开关选着输给阀信号的类型The +/- switch connects the valve Q command signal to the non-i
13、nverting (+vegives P A) and inverting (+ve gives P B) inputs.这个“+/-”开关是连接阀的Q指令开关，开关在“+”位置（阀给油P A）输入，在“-”位置（阀给油P B）输入。1.4.2 Spool滑阀The spool position signal from the valve is always available at the green spooltest point and passed on to the plant electronics regardless of the mode ofoperation. The g
14、reen spool test point gives a 0 to 10V signal proportional tothe spool signal from the valve. The LED display to the left of the test pointprovides a rudimentary indication of the signal. The centre blue null LED willbe illuminated when the spool signal is less than 10%.不论哪种控制模式下，从阀来的阀芯位置信号总是在测试点上呈绿色，这些绿色测试点上的电信号与提供的0 10V电信号成正比例。LED指示灯显示左边的测试点的迹象,提供了一个初步的信号，中心蓝色的LED零位指示灯在阀芯电信号小于10%时才亮。An understanding of the chec
