《NRF2401详细注释编程程序.doc》由会员分享，可在线阅读，更多相关《NRF2401详细注释编程程序.doc（11页珍藏版）》请在金锄头文库上搜索。
1、#include #include typedef unsigned char uchar;typedef unsigned char uint;/*NRF24L01端口定义*sbit MISO =P15;sbit MOSI =P14;sbit SCK =P13;sbit CE =P11;sbit CSN =P12;sbit IRQ =P16;/*按键*sbit KEY1=P26;sbit KEY2=P25;/*数码管位选*sbit led1=P24;sbit led2=P35;/*NRF24L01*#define TX_ADR_WIDTH 5 / 5 uints TX address wid
2、th#define RX_ADR_WIDTH 5 / 5 uints RX address width#define TX_PLOAD_WIDTH 20 / 20 uints TX payload#define RX_PLOAD_WIDTH 20 / 20 uints TX payloaduint const TX_ADDRESSTX_ADR_WIDTH= 0x34,0x43,0x10,0x10,0x01; /本地地址uint const RX_ADDRESSRX_ADR_WIDTH= 0x34,0x43,0x10,0x10,0x01; /接收地址/*NRF24L01寄存器指令*#define
3、 READ_REG 0x00 / 读寄存器指令#define WRITE_REG 0x20 / 写寄存器指令#define RD_RX_PLOAD 0x61 / 读取接收数据指令#define WR_TX_PLOAD 0xA0 / 写待发数据指令#define FLUSH_TX 0xE1 / 冲洗发送 FIFO指令#define FLUSH_RX 0xE2 / 冲洗接收 FIFO指令#define REUSE_TX_PL 0xE3 / 定义重复装载数据指令#define NOP 0xFF / 保留/*SPI(nRF24L01)寄存器地址*#define CONFIG 0x00 / 配置收发状态
4、，CRC校验模式以及收发状态响应方式#define EN_AA 0x01 / 自动应答功能设置#define EN_RXADDR 0x02 / 可用信道设置#define SETUP_AW 0x03 / 收发地址宽度设置#define SETUP_RETR 0x04 / 自动重发功能设置#define RF_CH 0x05 / 工作频率设置#define RF_SETUP 0x06 / 发射速率、功耗功能设置#define STATUS 0x07 / 状态寄存器#define OBSERVE_TX 0x08 / 发送监测功能#define CD 0x09 / 地址检测 #define RX_A
5、DDR_P0 0x0A / 频道0接收数据地址#define RX_ADDR_P1 0x0B / 频道1接收数据地址#define RX_ADDR_P2 0x0C / 频道2接收数据地址#define RX_ADDR_P3 0x0D / 频道3接收数据地址#define RX_ADDR_P4 0x0E / 频道4接收数据地址#define RX_ADDR_P5 0x0F / 频道5接收数据地址#define TX_ADDR 0x10 / 发送地址寄存器#define RX_PW_P0 0x11 / 接收频道0接收数据长度#define RX_PW_P1 0x12 / 接收频道0接收数据长度#d
6、efine RX_PW_P2 0x13 / 接收频道0接收数据长度#define RX_PW_P3 0x14 / 接收频道0接收数据长度#define RX_PW_P4 0x15 / 接收频道0接收数据长度#define RX_PW_P5 0x16 / 接收频道0接收数据长度#define FIFO_STATUS 0x17 / FIFO栈入栈出状态寄存器设置/*void Delay(unsigned int s);void inerDelay_us(unsigned char n);void init_NRF24L01(void);uint SPI_RW(uint uchar);uchar S
7、PI_Read(uchar reg);void SetRX_Mode(void);uint SPI_RW_Reg(uchar reg, uchar value);uint SPI_Read_Buf(uchar reg, uchar *pBuf, uchar uchars);uint SPI_Write_Buf(uchar reg, uchar *pBuf, uchar uchars);unsigned char nRF24L01_RxPacket(unsigned char* rx_buf);void nRF24L01_TxPacket(unsigned char * tx_buf);/*长延
8、时*void Delay(unsigned int s) unsigned int i; for(i=0; is; i+); for(i=0; i0;n-) _nop_();/*/*NRF24L01初始化/*/void init_NRF24L01(void) inerDelay_us(100); CE=0; / chip enable CSN=1; / Spi disable SCK=0; / SPI_Write_Buf(WRITE_REG + TX_ADDR, TX_ADDRESS, TX_ADR_WIDTH); / 写本地地址 SPI_Write_Buf(WRITE_REG + RX_AD
9、DR_P0, RX_ADDRESS, RX_ADR_WIDTH); / 写接收端地址 SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); / 频道0自动 ACK应答允许 SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); / 允许接收地址只有频道0，如果需要多频道可以参考Page21 SPI_RW_Reg(WRITE_REG + RF_CH, 0); / 设置信道工作为2.4GHZ，收发必须一致 SPI_RW_Reg(WRITE_REG + RX_PW_P0, RX_PLOAD_WIDTH); /设置接收数据长度，本次设置为32字节 SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x07); /设置发射速率为1MHZ，发射功率为最大值0dB/*/*函数：uint SPI_RW(uint uchar)/*功能：NRF24L01的SPI写时序/*/uint SPI_RW(uint uchar) uint bit_ctr; for(bit_ctr=0;bit_ctr8
