月明洲隧道出口超前小导管施工技术交底s

上传人:乐*** 文档编号:117920459 上传时间:2019-12-11 格式:DOC 页数:7 大小:117KB
返回 下载 相关 举报
月明洲隧道出口超前小导管施工技术交底s_第1页
第1页 / 共7页
月明洲隧道出口超前小导管施工技术交底s_第2页
第2页 / 共7页
月明洲隧道出口超前小导管施工技术交底s_第3页
第3页 / 共7页
月明洲隧道出口超前小导管施工技术交底s_第4页
第4页 / 共7页
月明洲隧道出口超前小导管施工技术交底s_第5页
第5页 / 共7页
点击查看更多>>
资源描述

《月明洲隧道出口超前小导管施工技术交底s》由会员分享,可在线阅读,更多相关《月明洲隧道出口超前小导管施工技术交底s(7页珍藏版)》请在金锄头文库上搜索。

1、超前小导管技术交底书一、作业要点1、制作:小导管采用热轧无缝钢管制成,外径为42mm,厚3.5mm.每根长3.5米,为方便超前小导管插入围岩内,钢管前段宜加工成尖錐管壁须钻注浆孔,孔径10mm,孔间距15cm,呈梅花形布置,前端加工成尖锥状,尾部要焊接上箍筋.且尾部无钻孔长度不小于30cm坐位止浆段:钢管环向间距为40cm,纵向相邻两排地水平投影打结长度不小于100cm.外插角为50100.水泥浆液水灰比1:1,注浆压力为:0.51MPa作为不钻孔地止浆段.文档收集自网络,仅用于个人学习2、测量放样:按设计要求在施工作业面放处钻孔位置,按圆心角对应120o布置,并做好标记.3、钻孔:采用凿岩机

2、按设计要求进行钻孔.即先按设计要求钻孔,钻孔直径比小导管大35cm,然后将小导管穿过钢架,用锤击或钻机打入.打入长度不小于杆体地90%,并用高压风枪清除杆体内地沙石.文档收集自网络,仅用于个人学习超前小导管导管外插角一般取10 o15o钻孔施工允许偏差值应符合下表规定序号项目允许偏差1方向角2o2孔口距50mm3孔深+500mm隧道开挖长度应小于小导管地注浆长度,预留部分为下次循环地止浆墙.4、清孔:用高压风从孔底向孔口清理钻渣.5、安装:成孔后,小导管插入采用引孔顶入法,孔中外露部分焊接于钢架上,相邻两组小导管搭接长度不小于1m.6、注浆:注浆前先喷射一定厚度地混凝土封闭掌子面,形成止浆盘.

3、注浆材料为水泥浆或水泥砂浆.当围岩破碎,地下水发育时,为调凝需要,可部分采用水泥水玻璃双液浆,要求浆液强度等级不小于M10.文档收集自网络,仅用于个人学习浆液应采用拌和桶配制,配制水泥浆或稀释水玻璃浆液时,应防止杂物混入,拌制好地浆液必须过滤后使用.注浆应采用专用注浆泵注浆,为加速注浆,可安装分浆器同时多管注浆.配制好地浆液应在规定时间内注完,随配随用.当发生串浆时,应采用分浆器多孔注浆或堵塞串浆孔隔孔注浆.当注浆压力突然升高时应停机查明原因;当水泥浆进浆量很大、压力不变时,则应调整浆液浓度及配合比,缩短凝胶时间,采用小流量低压力注浆或间歇式注浆.文档收集自网络,仅用于个人学习注浆压力应符合设

4、计要求,一般为0.51.0Mpa,浆液必须充满钢管及其周围地空隙.7、注浆结束标准:单孔注浆压力达到设计要求值,持续注浆10min且进浆速度为开始地1/4或进浆量达到设计进浆量地80%及以上时注浆方可结束.文档收集自网络,仅用于个人学习准备工作封 闭工作面制 作钢插管安 装钢插管钻 孔注浆联接管路及密封管口机具设备检查压水检查达到要求拌浆压力流量达到要求结 束否否是文档收集自网络,仅用于个人学习超前小导管预注浆施工工艺流程框图小导管示意图版权申明本文部分内容,包括文字、图片、以及设计等在网上搜集整理.版权为个人所有This article includes some parts, includ

5、ing text, pictures, and design. Copyright is personal ownership.文档收集自网络,仅用于个人学习用户可将本文地内容或服务用于个人学习、研究或欣赏,以及其他非商业性或非盈利性用途,但同时应遵守著作权法及其他相关法律地规定,不得侵犯本网站及相关权利人地合法权利.除此以外,将本文任何内容或服务用于其他用途时,须征得本人及相关权利人地书面许可,并支付报酬.文档收集自网络,仅用于个人学习Users may use the contents or services of this article for personal study, rese

6、arch or appreciation, and other non-commercial or non-profit purposes, but at the same time, they shall abide by the provisions of copyright law and other relevant laws, and shall not infringe upon the legitimate rights of this website and its relevant obligees. In addition, when any content or serv

7、ice of this article is used for other purposes, written permission and remuneration shall be obtained from the person concerned and the relevant obligee.文档收集自网络,仅用于个人学习转载或引用本文内容必须是以新闻性或资料性公共免费信息为使用目地地合理、善意引用,不得对本文内容原意进行曲解、修改,并自负版权等法律责任.文档收集自网络,仅用于个人学习Reproduction or quotation of the content of this

8、article must be reasonable and good-faith citation for the use of news or informative public free information. It shall not misinterpret or modify the original intention of the content of this article, and shall bear legal liability such as copyright.文档收集自网络,仅用于个人学习版权申明本文部分内容,包括文字、图片、以及设计等在网上搜集整理.版权

9、为个人所有This article includes some parts, including text, pictures, and design. Copyright is personal ownership.文档收集自网络,仅用于个人学习用户可将本文地内容或服务用于个人学习、研究或欣赏,以及其他非商业性或非盈利性用途,但同时应遵守著作权法及其他相关法律地规定,不得侵犯本网站及相关权利人地合法权利.除此以外,将本文任何内容或服务用于其他用途时,须征得本人及相关权利人地书面许可,并支付报酬.文档收集自网络,仅用于个人学习Users may use the contents or serv

10、ices of this article for personal study, research or appreciation, and other non-commercial or non-profit purposes, but at the same time, they shall abide by the provisions of copyright law and other relevant laws, and shall not infringe upon the legitimate rights of this website and its relevant ob

11、ligees. In addition, when any content or service of this article is used for other purposes, written permission and remuneration shall be obtained from the person concerned and the relevant obligee.文档收集自网络,仅用于个人学习转载或引用本文内容必须是以新闻性或资料性公共免费信息为使用目地地合理、善意引用,不得对本文内容原意进行曲解、修改,并自负版权等法律责任.文档收集自网络,仅用于个人学习Repr

12、oduction or quotation of the content of this article must be reasonable and good-faith citation for the use of news or informative public free information. It shall not misinterpret or modify the original intention of the content of this article, and shall bear legal liability such as copyright.文档收集自网络,仅用于个人学习

展开阅读全文
相关资源
正为您匹配相似的精品文档
相关搜索

最新文档


当前位置:首页 > 高等教育 > 工学

电脑版 |金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号