《模具英语专业术语资料》由会员分享，可在线阅读，更多相关《模具英语专业术语资料（5页珍藏版）》请在金锄头文库上搜索。
1、模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语 一、入水：gate 进入位(入水点)： gate location 水口形式： gate type 大水口(侧
2、浇口): edge gate 潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口: 细水口： pin-point gate 水口大小： gate size 转水口：switching runner/gate 唧嘴口径： sprue diameter直接水口: direct gate 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半
3、圆)流道： round(full/half) runner 矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner 流道电脑分析(模流分析)： mold flow analysis 流道平衡: runner balance 热嘴： hot sprue/tip 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line p
4、lug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold 二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold 叠层模: stacked mold边钉/导边：leader pin/guide pin 边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司： e
5、jector guide bush中托边： ejector guide pin 回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板： support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate 顶针板：ejector plate 底板: bottom clamp plate螺丝： screw 杯头螺丝: socket cup head screw平头螺丝: socket flat head
6、screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin 开模槽：ply bar socket 内模管位(模仁互锁)：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：sleeve ejector pin 缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： sl
7、ide 行位扣:镶件：insert 压座/斜鸡：wedge 耐磨板/油板： wear plate 压条：gib 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈(法兰)：locating ring 锁扣(模锁)：latch 扣鸡：parting lock set 推杆：push bar 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 型腔(前模仁): cavity型芯(
8、后模仁): core镶针：insert pin 销子(销钉)：dowel pin 波子弹弓：ball catch 喉塞(堵头): pipe plug 锁模块：lock plate 斜顶杆：angle ejector rod 斜顶针：angle from pin尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边(斜导柱)：angle pin 油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms 承压平面平衡：parting
9、 surface support balance 分模面排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes with ejector pin 料位出上/下模：part from cavity (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavit
10、y) insert 用铍铜做镶件： use beryllium copper insert 初步模图设计：preliminary mold design 正式模图设计： final mold design反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模(粘模)：sticking 顶白: stress mark热膨胀：thero expansion 缩水: shrinkage物料表: BOM原料: raw
11、 materials物料: materials工程试模材料: material for engineering mold testing成品: finished product 半成品: semi-finished product 公差：tolorance 铜公(电极)：copper electrode射料不足: short shot缺口: nick 瑕疪(斑点): speck 亮斑: shine 银纹: splay 焦痕: gas mark 起鳞: delamination 冷块: cold slug 导色: blush 沟槽;凿槽: gouge 段面咬花: satin texture 证示
12、线: witness line 专利: patent 沙砾: grit 细粒: granule=peuet=grain 抽粒机: grit maker 缓冲: cushion 不锈钢: stainless steel镁铝合金: magnalium 镁金属: magnesium 钣金: metal plate 车/车床: lathe 铣床/铣床: mill 刨/刨床: plane 磨/磨床: grind 钻/钻床: drill 镗: boring 气泡: blinster版次: revision 备注: remark 生产确认: production control confirmation 初审: checked by 核准: approved by 部门: department电镀: plate 成型: molding 样品: sample 雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching 回火: tempering 退火: annealing 碳化: carbonization铬酸处理: chromate 阳性处理: anodize氮化: nitrifying
