《as 3750.10-2008 paints for steel structures part 10 full gloss epoxy (two-pack)》由会员分享，可在线阅读，更多相关《as 3750.10-2008 paints for steel structures part 10 full gloss epoxy (two-pack)（33页珍藏版）》请在金锄头文库上搜索。
1、AS 3750.10-2008 Paints for steel structures Part 10 Full gloss epoxy (two-pack)AS 3750.102008 ?Australian StandardPaints for steel structures Part 10: Full gloss epoxy (two-pack) AS 3750.102008 This Australian Standard? was prepared by Committee CH-003, Paints and Related Materials. It was approved
2、on behalf of the Council of Standards Australia on 19 March 2007. This Standard was published on 19 May 2008. The following are represented on Committee CH-003: ?AUSTROADS ?Australasian Corrosion Association ?Australian Paint Approval Scheme ?Australian Paint Manufacturers Federation ?Australian Pip
3、eline Industry Association ?Business New Zealand ?Engineers Australia ?Institution of Professional Engineers New Zealand ?Master Painters Australia ?Master Painters New Zealand Association ?National Association of Testing Authorities Australia ?Water Corporation Western Australia This Standard was i
4、ssued in draft form for comment as DR 04190. Standards Australia wishes to acknowledge the participation of the expert individuals that contributed to the development of this Standard through their representation on the Committee and through the public comment period. Keeping Standards up-to-date Au
5、stralian Standards? are living documents that reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that re
6、aders assure themselves they are using a current Standard, which should include any amendments that may have been published since the Standard was published. Detailed information about Australian Standards, drafts, amendments and new projects can be found by visiting .standards.org.auStandards Austr
7、alia welcomes suggestions for improvements, and encourages readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at mailstandards.org.au, or write to Standards Australia, GPO Box 476, Sydney, NSW 2001. AS 3750.102008 ?Australian StandardPaints for steel s
8、tructures Part 10: Full gloss epoxy (two-pack) 睷眮抵晸眮捯?Originated as AS 26031983. Revised and redesignated as AS/NZS 3750.10:1994. Revised and redesignated as AS 3750.102008. COPYRIGHT ? Standards Australia All rights are reserved. No part of this work may be reproduced or copied in any form or by an
9、y means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published by Standards Australia GPO Box 476, Sydney, NSW 2001, Australia ISBN 0 7337 8663 4 AS 3750.1020082 PREFACE This Standard was prepared by the Australian members of the Joint Standards
10、 Australia/Standards New Zealand Committee CH-003, Paints and Related Materials to supersede AS/NZS 3750.10:1994. The objective of this Standard is to provide requirements for full gloss epoxy paint intended for use on iron and steel structures. It forms part of a series of product Standards for pai
11、nts referred to in AGSu/NidZe Sto 2 t3h1e2 p, rotection of structural steel against atmospheric corrosion by the use o.8f protective coatingsSee AS/NZS 3750.0 for other published Standards in this series. The terms normative and informative have been used in this Standard to define the application o
12、f the appendix to which they apply. A normative appendix is an integral part of a Standard, whereas an informative appendix is only for information and guidance. 睷眮抵晸眮捯? 3 AS 3750.102008CONTENTS PageSECTION 1 SCOPE AND GENERAL 1.1 SCOPE.4. . 1.2 REFERENCED DOCUMENTS.4 1.3 DEFINITIONS.4 1.4 SAFETY PRECAUTIONS.4 SECTION 2 MATERIALS REQUIREMENTS 2.1 GENERAL.5 2.2 CONDITIONS OF TEST.5 2.3 LIQUID PAINT.5 2.4 APPLICATION PROPERTIES.6 2.5 APPLIED FILM.6 SECTION 3 PACKAGING AND LABELLING 3.1 MIXING RATIO.11 3.2 PACKAGING.
