模压产品公差

《模压产品公差》由会员分享，可在线阅读，更多相关《模压产品公差（4页珍藏版）》请在金锄头文库上搜索。

1、橡胶制品公差模压制品公差标称尺寸M1级M2级M3级M4级以上以下FCFCFCF&C04.06.310162540631001604.06.31016254063100160-0.080.100.100.150.200.200.250.350.400.3%0.100.120.150.200.200.250.250.400.500.4%0.100.150.200.200.250.350.400.500.700.5%0.150.200.200.250.350.400.500.700.800.8%0.250.300.400.500.600.801.001.300.8%0.400.500.600.801

2、.001.301.602.001.3%0.50.700.801.001.301.602.002.501.5%无支承挤压制品的截面尺寸公差标称尺寸等级E1等级E2等级E3以上以下01.52.54.006.3010162540631.52.54.006.301016254063-0.150.200.250.350.400.500.700.801.001.300.250.350.400.500.700.801.001.301.602.000.400.500.700.801.001.301.602.002.503.20芯棒支承的挤压制品的截面尺寸公差 单位： mm(另有规定除外)标称尺寸等级EN1等级

3、EN2等级EN3以上以下046.3101625406310016046.31016254063100160-0.200.200.250.350.400.500.700.801.000.6%0.200.250.350.400.500.700.801.001.300.8%0.350.400.500.700.801.001.301.602.001.2%表面光洁的挤压制品的外部尺寸公差 单位： mm(另有规定除外)标称尺寸等级EG1等级EG2以上以下010162540631001601016254063100160-0.150.200.200.250.350.400.500.3%0.250.350.4

4、00.500.700.801.000.5%表面光洁的挤压制品的壁厚尺寸公差 单位： mm(另有规定除外)标称尺寸等级EW1等级EW2以上以下046.3101646.31016250.100.150.200.200.250.200.200.250.350.40挤压制品的长度尺寸公差 单位： mm(另有规定除外)标称尺寸等级EN1等级EN2等级EN3以上以下040631001602504006301000160025004000406310016025040063010001600250040000.70.81.01.31.62.02.53.24.05.06.30.161.01.31.62.02.

5、53.24.05.06.310.012.50.32%1.62.02.53.24.05.06.310.012.516.020.00.5%挤压制品的切面尺寸公差 单位： mm(另有规定除外)标称尺寸等级EN1等级EN2等级EN3以上以下0.631.001.602.504.006.310161.001.602.504.006.301016250.100.100.150.200.200.250.350.400.150.200.200.250.350.400.500.700.200.250.350.400.500.700.801.00压延胶板的厚度误差标称厚度等级ST1等级ST2等级ST3以上以下01.001.602.504.006.3010161.001.602.504.006.3010160.150.150.20.250.350.40.53.50.20.250.350.40.50.70.850.250.350.40.50.70.81.07压延胶板的宽度误差标称宽度等级SW1等级SW2等级SW3以上以下63010001600100016002030225402.530503