《插件国巨电阻规格书》由会员分享，可在线阅读，更多相关《插件国巨电阻规格书（9页珍藏版）》请在金锄头文库上搜索。
1、 Page-1 Approval Sheet for Carbon Film Resistors CFR series 2% & 5% YAGEO CORPORATION Headquarters: 3F, No.233-1, Pao Chiao Rd., Shin Tien, Taipei, Taiwan, R.O.C. Tel: 886-2-2917-7555 Fax: 886-2-2917-4286 URL: .tw Page-2 Page-3 1. PRODUCT: CARBON FILM RESISTORS (Normal & Miniature Style) 2. PART NUM
2、BER: Part number of the carbon film resistor is identified by the name, power, tolerance, packing, temperature coefficient, special type and resistance value. Example： CFR -12 J T J 52 100R Series Size Resistance Packing Temperature Special Resistance Name Code Tolerance Style Coefficient Type Value
3、 of Resistance (1) Style: CFR SERIES (2) Power Rating: -12=1/6W、25S=1/4WS、-25=1/4W、50S=1/2WS、-50=1/2W、 1WS=1WS、100=1W、2WS=2WS、200=2W (3) Tolerance: G=2% J=5% (4) Packaging Type: RPaper Taping Reel TTape on Box Packing BBulk Packing (5) T.C.R: J=350ppm/ =lgnore (6) Special Type: 2626mm、52=52.4mm、73=7
4、3mm、 PNPANAsert AVAVlsert (7) Resistance Value: 1R、10R、100R、10K、100K、330K、1M Page-4 3. BAND-CODE: 4. ELECTRICAL CHARACTERISTICS Tabe I *Standard resistance is 1 10M, below or over this resistance on request. *Rated Continuous Working Voltage (RCWV)=Value ResistanceRatingPower FIG.1 TEMPERATURE COEFF
5、ICIENT Page-5 5. DERATING CURVE & HOT-SPOT TEMPERATURE 6. DIMENSIONS 7. ENVIRONMENTAL CHARACTERISTICS (1) Short Time Over Load Test At 2.5 times of the rated voltage. (If the voltage exceeds the maximum load voltage, the maximum load voltage will be used as the rated voltage) applied for 5 seconds,
6、the resistor should be free from defects after the resistor is released from load for about 30 minutes and the change of the resistance value should be within (0.25%+0.05) as compared with the value before the test. Page-6 (2) Dielectric Withstanding Voltage The resistor is placed on the metal V Blo
7、ck. Apply a Table I dielectric withstanding between the terminals connected together with the block for about 60 seconds. The resistor shall be able to withstand without breakdown or flashover. (3) Temperature Coefficient Test Test of resistors above room temperature 125C to 130C (Testing Temperatur
8、e) at the constant temperature silicon plate for over 4 to 5 minutes. Then measure the resistance. The Temperature Coefficient is calculated by the following equation and its value should be within the range of requested. 600010tt1RRRtCoefficieneTemperatursistorRe = = = = R Resistance value under th
9、e testing temperature R0 Resistance value at the room temperature t The testing temperature to Room temperature (4) Insulation Resistance Apply test terminal on lead and resistor body. The test resistance should be high than 10,000 Mohm. (5) Solderability Immerse the specimen into the solder pot at
10、2305C for 50.5 seconds. At least 95% solder coverage on the termination. (6) Resistance to Solvent The specimen into the appropriate solvent of Methyleme Chloride condition of ultrasonic machine for 1 minutes. The specimen is no deterioration of coatings and color code. (7) Terminal Strength Direct
11、Load Resistors shall be held by one terminal and the load shall be gradually applied in the direction of the longitudinal axis of the resistor unit the applied load reacheds 5 pounds. The load shall be held for 10 seconds. The load of weight shall be 2.5kg(24.5N). Page-7 (8) Pulse Overload Apply 4 t
12、imes of rated voltage to the specimen at the 1 second on and 25 seconds off cycle, subjected to voltage application cycles specified in 10000. The change of the resistance value shall be within (2%+0.05). (9) Load Life in Humidity Place the specimen in a test chamber at 402C and 9095% relative humid
13、ity. Apply the rated voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1000 hours. The change of the resistance value shall be within (1.5%+0.05). (10) Load Life Test Placed in the constant temperature chamber of 703C the resistor shall be connected to t
14、he lead wire at the point of 25mm. Length with each terminal, the resistors shall be arranged not much effected mutually by the temperature of the resistors and the excessive ventilation shall not be performed, for 90 minutes on and 30 minutes off under this condition the rated D.C. voltage is appli
15、ed continuously for 1000+48/-0 hours then left at no-load for 1hour, the change of the resistance value measured at this time to the value before the test shall be within (1.5%+0.05). There shall be no remarkable change in the appearance and the color code shall be legible after the test. (11) Tempe
16、rature Cycling Test The temperature cycle shown in the following table shall be repeated 5 times consecutively. The measurement of the resistance value is done before the first cycle and after ending the fifth cycle, leaving in the room temperature for about 1 hour, the change shall be within (1%+0.
17、05). After the test the resistor shall be free from the electrical or mechanical damage. Temperature Cycling Conditions: Step Temperature(C) Time (minute) 1 +25+10 -5 10 to15 2 -65+0 -3 30 3 +25+10 -5 10 to15 4 +150+3 -0 30 Page-8 (12) Resistance to Soldering Heat The terminal lead shall be dipped i
18、nto the solder pot at 35010C for 30.5 seconds up to 3 mm. The change of the resistance value shall be within (1%+0.05). 8. PACKING METHODS Bandolier for Axial leads The resistors are supplied on bandolier, either 1000 resistors in ammopack or 5000 resistors on reel. 9. TAPE ON REEL PACKING & TAPE ON BOX PACKING Page-9 10. SPECIAL TYPE (FORMING DIMENSIONS)
