《焊接工艺评定报告Q345ET45》由会员分享，可在线阅读，更多相关《焊接工艺评定报告Q345ET45（5页珍藏版）》请在金锄头文库上搜索。
1、焊接工艺评定报告Weldi ng Procedure Qualificati on Report评定项目 / Qualification Items：Q345E + Q345E气体保护焊 /Gas-shielded Metal-arc Welding 评定报告编号 / Qualification Report NO. :P08-02评定日期/Date: 编制 /Written :审核/Authorized : 用户确认 / Customer Signature焊接工艺评定记录Weld ing Procedure Qualificati on Report公司名称：Corporate Name
2、:工艺评定报告编号/ PQR NO.:日期/Date:焊接工艺规程编号/ WPS NO.:焊接方法 /Welding Method :气体保护焊_/Gas-shielded_Metal-arc Welding接头 /Weld Joi nt接头形式/Joint Type :X 型 X type衬垫 /Weld Back :无 /None机械化程度 / Mechanized degree:半自动化 / Semiautomation焊接简图 /Welding Single Drawing :/ 99.2%流量 /Gas Flow15-20l/min其它 /Other/摆动或不摆动/Weaving W
3、elding Yes 摆动参数/ Weaving Parameter 手工 manual多道焊或单道焊(每面)/Multipss Welding or One-pass Welding ( Every Surface) 多道Multiple welding电特性 /Electricity Feature :电流种类 /Current KindDirect Current / DC极性 /PolrityReversed Polrity /EP电流 /Current 240-280A 电压 /Voltage 30-32 V 其它 /Other/单丝焊或多丝焊 /One-wire or Multip
4、le-wire Welding 单丝 /sinale type of welding wire 其它 /Other/焊缝外观检查 /Visual Inspection of Completed Welds :焊缝表面焊波均匀，无明显咬边、凹凸不平等缺陷。外观检杳合格No undercut亠No sags and crests,No defect acceptable.无损检测 /Non-Destructive Examination :1 .超声波探伤(标准号、结果)/Ultrasonic Testing(Standard Number、Result)GB/T11345-89B 级合格 / a
5、cceptable2.射线探伤（标准号、结果）/Radiographicl Testing(Standard Number、Result)3.磁粉探伤（标准号、结果）/Mag netic Particle Test in g(Sta ndard Number、Result)4.着色探伤（标准号、结果）/Penetrant Testing(Standard Number、Result)其它 /Other 拉伸试验 /Tensile Testing试样号宽(mm)厚(mm)面积(mmA2)断裂载荷（N）抗拉强度/Rm断裂特点和部位Coupon NO.WidthThicknessAreaCracki
6、ng Load(N/mmA2)Cracking Feature&Place2-1 1078.5441000522母材处 /base crack2-2 1078.5441000522母材处 /base crack2-3 1078.5442000535母材处 /base crack弯曲试验/Bend Testing试样号Coupon NO.试样类型Coupon Type弯轴直径Bending Shaft Diameter试验结果Testi ng Result2-1侧弯 180 /site bend 180a =3 a合格 / acceptable2-2侧弯 180 /site bend 180a
7、=3 a合格 / acceptable2-3侧弯 180 /site bend 180a =3 a合格 / acceptable冲击试验 /Notch Impact Testing试样号缺口位置缺口形式试验温度（C）冲击吸收功（J）Coupon NO.Notch PlaceNotch TypeTemperatureMi n. Notch Impact En ergy2-1HAZ热影响V-40 C101KN2-2HAZ热影响V-40 C104KN2-3HAZ热影响V-40 C103KN:2-1WELD焊缝区V-40 C104KN2-2WELD焊缝区V-40 C103KN2-3WELD焊缝区V-4
8、0 C104KN结论 /Result:本评定按美国机械工程师学会(ASME )规范第区卷的规定焊接试件、检验试样、测定性能、确认试验记录正确。This Welding Procedure Qualification Report according to ASME paragraphIX to weld the test sample ,test the ample, determ inat the performa nee, and con firmat the testi ng record is correct 。评定结果 /Judgment result(合格 /Yos)焊工 /Operator(签字 /Signature):日期/Date:标记 /marker:填表 /Writte n(签字 /Signature):日期/Date:标记 /marker:审核 / Authorized(签字 /Signature):日期/Date:
