《stm32F1外部脉冲计数(库函数实现》由会员分享，可在线阅读，更多相关《stm32F1外部脉冲计数(库函数实现（4页珍藏版）》请在金锄头文库上搜索。
1、主函数#include stm32f10x.h#include timer.h#include led.h#include delay.h#include oled.h#include sys.hint main(void) u16 t=0; delay_init(); LED_Init(); TIM3_PWM_Init(9999,719); TIM2_Excnt_Init(10); OLED_Init(); NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); OLED_ShowString(20,0,EXCNT_TEST,16); OLED_Ref
2、resh_Gram(); TIM_SetCompare2(TIM3,1000); while(1) delay_ms(1);t=TIM_GetCounter(TIM2); OLED_ShowNum(20,30,t,6,16); OLED_Refresh_Gram(); timer.c#include timer.h#include led.h#include usart.h#include oled.hvoid TIM3_PWM_Init(u16 arr,u16 psc) GPIO_InitTypeDef GPIO_InitStructure;TIM_TimeBaseInitTypeDef T
3、IM_TimeBaseStructure;TIM_OCInitTypeDef TIM_OCInitStructure;RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE); /使能GPIO外设和AFIO复用功能模块时钟使能GPIO_PinRemapConfig(GPIO_PartialRemap_TIM3, ENABLE); /Timer3部分重映射 TIM3_CH2-PB5 /用于TIM3的C
4、H2输出的PWM通过该LED显示 /设置该引脚为复用输出功能,输出TIM3 CH2的PWM脉冲波形GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5; /TIM_CH2GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; /复用推挽输出GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOB, &GPIO_InitStructure);/GPIO_WriteBit(GPIOA, GPIO_Pin_7,Bit_SET); / PA7上拉TIM_TimeB
5、aseStructure.TIM_Period = arr; /设置在下一个更新事件装入活动的自动重装载寄存器周期的值 80KTIM_TimeBaseStructure.TIM_Prescaler =psc; /设置用来作为TIMx时钟频率除数的预分频值 不分频TIM_TimeBaseStructure.TIM_ClockDivision = 0; /设置时钟分割:TDTS = Tck_timTIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; /TIM向上计数模式TIM_TimeBaseInit(TIM3, &TIM_Time
6、BaseStructure); /根据TIM_TimeBaseInitStruct中指定的参数初始化TIMx的时间基数单位 TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2; /选择定时器模式:TIM脉冲宽度调制模式2TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; /比较输出使能TIM_OCInitStructure.TIM_Pulse = 0; /设置待装入捕获比较寄存器的脉冲值TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPol
7、arity_High; /输出极性:TIM输出比较极性高TIM_OC2Init(TIM3, &TIM_OCInitStructure); /根据TIM_OCInitStruct中指定的参数初始化外设TIMxTIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable); /使能TIMx在CCR2上的预装载寄存器TIM_ARRPreloadConfig(TIM3, ENABLE); /使能TIMx在ARR上的预装载寄存器 TIM_Cmd(TIM3, ENABLE); /使能TIMx外设 /定时器2外部脉冲计数函数void TIM2_Excnt_Init(u16
8、arr) GPIO_InitTypeDef GPIO_InitStructure;TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;NVIC_InitTypeDef NVIC_InitStructure;RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);/使能GPIOA和TIM2的时钟RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);TIM_DeInit(TIM2);GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IN
9、_FLOATING;GPIO_InitStructure.GPIO_Pin=GPIO_Pin_0;GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;GPIO_Init(GPIOA, &GPIO_InitStructure);TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1;TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up;TIM_TimeBaseStructure.TIM_Period=arr;TIM_TimeBaseStructu
10、re.TIM_Prescaler=0;TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure); TIM_ETRClockMode2Config(TIM2,TIM_ExtTRGPSC_OFF,TIM_ExtTRGPolarity_NonInverted,10); /ExtTRGFilter：外部触发滤波器。该参数取值在0x0和0xF之间。在我所在的环境下设置为10经检测最准确。NVIC_InitStructure.NVIC_IRQChannel=TIM2_IRQn;NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;NVI
11、C_InitStructure.NVIC_IRQChannelPreemptionPriority=1;NVIC_InitStructure.NVIC_IRQChannelSubPriority=3;NVIC_Init(&NVIC_InitStructure); /中断优先级设置，抢占优先级为1，响应优先级为3TIM_ITConfig(TIM2,TIM_IT_Update|TIM_IT_CC1,ENABLE);/使能TIM2中断TIM_SetCounter(TIM2,0);TIM_Cmd(TIM2,ENABLE);void TIM2_IRQHandler(void)if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET)LED1=!LED1;TIM_ClearITPendingBit(TIM2, TIM_IT_CC1|TIM_IT_Update);
