Technical SpecificationTS C302 V1.0.0 (1999-10)China Wireless Telecommunication Standard (CWTS); Working Group 1 (WG1);Mobile Station Conformance Testing 2Mobile Station Conformance Testing Intellectual Property RightsForewordINTELLECTUAL PROPERTY RIGHTS 2FOREWORD 21 SCOPE 42 REFERENCES 43 DEFINITIONS, SYMBOLS, AND ABBREVIATIONS 53.1 Definitions 53.2 Symbols 53.3 Abbreviations 54 FREQUENCY BANDS AND CHANNEL ARRANGEMENT 64.1 General 64.2 Frequency bands 64.3 TX–RX frequency separation 64.4 Channel arrangement 64.4.1 Channel spacing 64.4.2 Channel raster 64.4.3 Channel number 65 GENERAL TEST CONDITIONS AND DECLARATIONS 75.1 UE classes 75.2 Output power and determination of power class 75.3 Specified frequency range 75.4 Test environments 75.4.1 Normal test environment 75.4.2 Extreme test environment 85.4.3 Vibration 95.4.4 Power supply 95.4.5 Acceptable uncertainty of measurement equipment 95.5 Interpretation of measurement results 135.6 Selection of configurations for testing 135.7 UE Configurations 135.7.1 Receiver diversity 135.7.2 Duplexers 135.7.3 Power supply options 135.7.4 Ancillary RF amplifiers 145.7.5 UE using antenna arrays 145.8 Overview of the conformance test requirements 145.9 Format and interpretation of tests 166 TRANSMITTER CHARACTERISTICS 166.1 General 166.2 Maximum output power 176.2.1 Definition and applicability 176.2.2 Conformance requirements 176.2.3 Test purpose 176.2.4 Method of test 176.2.5 Test requirements 176.3 Frequency stability 186.3.1 Definition and applicability 186.3.2 Conformance requirements 186.3.3 Test purpose 186.3.4 Method of test 186.3.5 Test requirements 196.4 Output power dynamics 196.4.1 Closed loop power control 196.4.2 Power control steps 196.4.3 Power control dynamic range 206.4.4 Minimum transmit power 206.4.5 Total power dynamic range 216.4.6 Power control cycles per second 216.5 Transmit OFF power 216.5.1 Definition and applicability 216.5.2 Conformance requirements 216.5.3 Test purpose 21This test verifies the ability of theUE to reduce its transmit OFF power to a value below the specified limit. This ability is needed to minimize the interference for other users receiving on the same frequency.6.5.4 Method of test 216.5.5 Test requirements 216.6 Output RF spectrum emissions 216.6.1 Occupied bandwidth 216.6.2 Out of band emission 216.6.3 Spurious emissions 216.7 Transmit intermodulation 216.7.1 Test purpose 216.7.2 Test case 216.7.3 Conformance requirements 216.8 Transmit Modulation 216.8.1 Transmit pulse shape filter 216.8.2 Modulation accuracy 216.8.3 Peak Code Domain Error 217 RECEIVER CHARACTERISTICS 217.1 General 217.2 Reference sensitivity level 217.2.1 Minimum requirement 217.2.2 Maximum frequency deviation for receiver performance 217.3 Dynamic range 217.3.1 Test purpose 217.3.2 Test case 217.3.3 Conformance requirements 217.4 Adjacent Channel Selectivity (ACS) 217.4.1 Test purpose 217.4.2 Test case 217.4.3 Conformance Requirements 217.5 Blocking characteristics 217.5.1 Test purpose 217.5.2 Test case 217.5.3 Conformance requirements 217.6 Intermodulation characteristics 217.6.1 Test purpose 217.6.2 Test case 217.6.3 Conformance requirements 217.7 Spurious emissions 217.7.1 Test purpose 217.7.2 Test case 217.7.3 Conformance requirements 218 PERFORMANCE REQUIREMENTS 218.1 General 218.2 Dynamic reference sensitivity performance 218.2.1 Performance in AWGN channel 218.2.2 Performance in multipath fading channels 218.3 UE synchronisation performance 218.3.1 Test purpose 218.3.2 Test case 218.3.3 Conformance requirements 21A.1 General 21A.2 Definition of the process 21A.2.1 Basic principle 21A.2.2 Output signal of the Tx under test 21A.2.3 Reference signal 21A.2.4 Provisions in case of multi code signals 21A.2.5 Classification of measurement results 21A.2.6 Process definition to achieve results of type 1 21A.2.7 Process definition to achieve results of type 2 21A.3 Applications 21HISTORY 211 Scope The present document specifies the Radio Frequency (RF) test methods and conformance requirements for TD-SCDMAUE operating in the TDD mode. These have been derived from, and are consistent with, the TD-SCDMA specifications defined in CWTS TS C401 [1]. In this TS, the reference point for RF connections (except for the measurement of mean transmitted RF carrier power) is the antenna connector, as defined by the manufacturer. This TS does not apply to repeaters or RF devices which may be connected to an antenna connector of a UE.2 ReferencesThe following documents contain provisions which, through reference in this text, constitute provisions of the present document.· References are either specific (identified by date of publication, edition number, version number, etc.。
