《板冰机说明15380V1》由会员分享，可在线阅读，更多相关《板冰机说明15380V1（30页珍藏版）》请在金锄头文库上搜索。
1、板冰机操作说明Ice Plate Machine Operation Manual使 用 说 明 书Manual Book 广州冰泉制冷设备有限责任公司 Guangzhou Icesource Refrigeration Equipment Co., Ltd. 安装、使用本机组之前，请仔细阅读本说明书。Please carefully read this manual before installing and using the machine. 目录 Catalog广州冰泉制冷设备有限责任公司- 0 -Guangzhou Icesource Refrigeration Equipment
2、Co., Ltd.- 0 -、引言（Introduction)- 2 -II、注意事项 (Attention )- 2 -III、安装 (Installation)- 3 -3.1.冰机配件(Ice machine accessories)- 3 -3.2.制冰机安装(Install the ice-maker)- 3 -3.3.水管连接(Pipe connection)- 4 -3.4. 冷却水塔 (Assembly of the Cooling Tower)- 5 -3.5. 安装完成(The installation is complete)- 8 -3.6 风冷型冰机 (Air-coo
3、led type ice machine)- 8 -3.7连接电线 (Connect the wire)- 9 -IV、制冰原理 (Ice making theory)- 10 -V、电箱电器布置 (Electricity box arangement)- 11 -VI控制面板 (Control panel)- 12 -6.1主画面（ Main screen）- 12 -6.3模拟画面 Simulation picture- 13 -6.4 PLC画面 PLC screen- 14 -6.5 故障保护画面 Fault protection screen- 15 -6.6故障查询 Fault d
4、iagnosis- 16 -6.7 产品展示 Product display- 17 -6.8 联系我们 Contact us- 17 -6.9开关与按钮 (The switch and the button)- 18 -VII. 清洗程序 (Cleaning Procedures)- 18 -VIII. 冰块厚度调节 (Adjusting the thickness of cube ice)- 19 -IX. 主要技术参数 (The main technical parameters)- 19 -X. 故障现象及排除(Malfunction Phenomena & Elimination)-
5、 20 -XI维修说明 (Maintain statement)- 25 -XII. 附图 （Attached Drawing）- 25 -、引言（Introduction) 该设备是我们的工程师和技术人员在制冷领域长期经验的结晶，已在我们现代化的制造场所内得到精心的装配。使用设备前请认真阅读这些说明。The equipment is crystallization by our engineers and technicians with long experience in the field of refrigeration, which has been assembled well
6、in our modernization manufacturing site. Before use the equipment you must read these instructions carefully.II、注意事项 (Attention )1. 使用前应认真阅读此说明书。2. 机组电源必须符合如下规定：额定电源：三相AC380V，50Hz.(可以根据客户的需要使用相应的电压，如3P-AC220V,60HZ）电压变动范围：额定电压10%以下相间电压不平衡：2.5%以下频率变动：额定频率2%以下注：若不能确定电源符合以上条件，请选配相应的保护器，否则会损坏压缩机。3. 确保PLC
7、亮绿灯，若亮灯异常请与厂家联系。4. 确保供电电源接线牢固可靠、接触良好。5. 切勿使用坚硬、尖锐的物体按压控制面板按钮，否则控制器可能损坏。6. 机组安装时应保持相对的水平和垂直位置。7. 当出现异常现象，立即停机，断电检修。8. 开机前请确认压缩机吸、排气阀已经全部打开，否则会造成压缩机严重损伤9. 开机前请确认储液器上的供液阀已经全部打开，否则机组无法正常运行。10. 为保证机组数据不被丢失，请保持机组持续供电。11. 保持机组持续供水，否则会因缺水而造成循环水泵烧损。12. 本机组厂家已设定的参数，如用户修改，后果自负。13. 非专业维修人员绝对不许修理产品。以免发生人身伤害事故。14
8、. 电源设计专用回路。电源线请勿在中途连接、使用延长线。以免引起触电、火灾。15. 请勿将硬物靠近出冰螺杆。以免损坏螺杆、引起人身伤害事故。16. 请勿触摸工艺管道。以免引起人身伤害事故。17. 对压缩机、管道进行检测、维修时，带上安全眼镜、手套。18. 利用叉车叉冰机时，务必对准冰机底座的两个长方孔，将两条叉柄伸入到冰机底座1米以上，才能移动冰机，此过程中确保稳定。19.制冰机开机前，须让系统通电8小时以上，使油加热器将润滑油加热到45-50，（加热至视油镜中能观察到油面），使润滑油中的制冷剂充分气化，以防止压缩机磨损或液击而影响压缩机的使用寿命。1. Please read this ma
9、nual book carefully before using.2. The power supply of machine must meet the following rules：The rated power supply: Three phases AC380V, 50 Hz.（According to the requirements of the customers can use the corresponding voltage, such as 3P-AC220V,60HZ)The scope of the voltage changes: 10% of the rate
10、d voltage.Alternate voltage unbalance: 2.5%Frequency fluctuation: 2% of the rated frequencyNote: If you cant make sure whether the power supply matches the above conditions, please choose the corresponding protector; otherwise it will damage the compressor.3. Make sure the light of PLC is green. If
11、the light is abnormal, please contact the factory.4. Make sure the power supply lines connect firmly and properly.5. Dont use the hard, tough and sharp objects to press the control panel button, otherwise controller may be damaged.6. Keep the relatively horizontal and vertical positions when install
12、 the machine.7. When the abnormal phenomenon appears, please shut it down immediately, and cut off the power to check.8. Please confirm the suction and exhaust valves of the compressor have been open before starting the ice-maker, otherwise it will damage the compressor badly.9. Please confirm all v
13、alves on the fluid reservoir have been opened，otherwise the ice-maker can not work normally.10. Please offer the power to the ice-maker continuously in order to keep the data from not being lost. 11. Please offer water to the ice-maker continuously in order to prevent the circulating water pump from
14、 being damaged because of water shortage.12. The factory has set a fixed parameter, if the user revises it, the user will take all the risk.13. Non-professional staff are absolutely forbidden to fix the product, in order to avoid personal injure accident.14. The power design adopts special circuit.
15、Please do not connect in the midway or use extension line with the power cable, in order to prevent causing electric shock sor fires.15. Please do not make hard things approach the ice convey screw in order to prevent damaging the screw and causing personal injure accident.16. Do not touch the pipes in order to cause personal injure accident.17. Please wear safe glasses and gloves, when make on the examination and maintenance to the compressor and pipes.
