《DELL硬盘LED灯含义》由会员分享，可在线阅读，更多相关《DELL硬盘LED灯含义（5页珍藏版）》请在金锄头文库上搜索。
1、文档供参考，可复制、编制，期待您的好评与关注！ Power-on Green indicates that the power supply is operational. Fault Red indicates a problem with the power supply (fan failure, voltage error, etc.). Power present Green indicates that power is present at the power supply and that the system is connected to a power source. 上
2、电绿色表示电源正常运行。故障红色表示是电源供应器（风扇故障，电压错误等）的问题。电源存在绿色表示电源在电源存在，而且该系统已连接至电源。Component Description Power button Turns system power off and on.If you turn off the system using the power button and the system is running an ACPI-compliant operating system (such as Microsoft Windows 2000), the system can perform
3、 an orderly shutdown before power is turned off. If the system is not running an ACPI-compliant operating system, power is turned off immediately after the power button is pressed. The button is enabled in the System Setup program. When disabled, the button can only turn system power on. For more in
4、formation, see the Users Guide and the operating systems documentation. Power indicator Provides information on power status (see Power Indicator Codes). CD and diskette drive indicators Indicates read or write access to the respective drive. hard-drive indicators Provide information on the status o
5、f the respective hard drive (see SCSI Hard-Drive Indicator Codes). NIC indicators Indicate whether the NIC has a valid link to the network (see NIC Indicator Codes). Status LCD Can signify when the system is operating correctly or when the system needs attention (see LCD Status Messages). System ide
6、ntification button Can be used to identify a particular system (see System Identification Indicators). NMI button Can be used to troubleshoot software and device driver errors when using certain operating systems. This button is often referred to as a force dump switch and can be pressed using the e
7、nd of a paper clip. When the option is enabled in the System Setup program and the button is pressed, an NMI alerts the system.Use this button only if directed to do so by qualified support personnel or by the operating systems documentation. For more information, see the Users Guide and the operati
8、ng systems documentation.组件说明电源按钮打开和关闭系统电源。如果您关闭系统使用的电源按钮和系统运行的是ACPI兼容操作系统（如微软 Windows 2000），系统可以执行正常的关机前关闭电源。如果系统运行的不是ACPI兼容操作系统，关闭电源后，立即按下电源按钮。启用该按钮在系统设置程序。禁用时，该按钮只能打开系统电源。有关详细信息，请参阅用户指南和操作系统的文档。电源指示灯提供有关电源状态（请参阅“电源指示灯代码“）。CD和软盘驱动器指示灯指示读或写访问相应的驱动器。硬盘驱动器指示灯提供关于各自的硬盘驱动器（请参阅“SCSI硬盘驱动器指示灯代码“）的状态信息。网卡指
9、标说明是否网卡都有一个网络（见“NIC指示灯代码“）的有效链接。液晶状态可以意味着当系统运行正常，或当系统需要关注（见“LCD状态消息“）。系统识别按钮可用于识别特定的系统（请参阅“系统识别指示灯“）。NMI按钮可用于排除软件和设备驱动程序错误时使用某些操作系统。这个按钮通常被称为“空军场开关“，可以按使用的一个文件夹结束。当启用该选项在系统设置程序并按下按钮，一个NMI警报系统。如果只把这个指示做合格的支持人员或操作系统说明文件按钮。有关详细信息，请参阅用户指南和操作系统的文档。Drive Status Indicator Indicator Code Drive bay empty, re
10、ady for insertion or removal Off Drive being prepared for operation, drive onlineSteady green Drive being identified Blinks green four times per second Drive being prepared for removal Blinks green twice per second at equal intervals Drive rebuilding Blinks green twice per second at unequal interval
11、s Drive failed Blinks amber four times per second Predicted failure for the drive Blinks green, then amber, and then off, repeating this sequence every two seconds NOTE: The drive busy indicator signifies whether the hard drive is active on the SCSI bus. This indicator is controlled by the hard drive. 驱动器状态指示灯指标代码驱动器托架空，准备插入或卸下关车道正准备操作，提高线上稳定的绿色车道被确定呈绿色闪烁四次每秒车道正准备搬迁闪烁绿色两次在相同的时间间隔为每秒车道重建闪烁绿色两次每秒不等的时间间隔车道失败琥珀色闪烁四次每秒预报故障的驱动器闪烁绿色，然后琥珀色，然后再关上，重复此顺序每两秒钟注意：驱动器忙指示灯表示硬盘驱动器是否在SCSI总线上活跃。该指标是由硬盘驱动器。 /
