《PCBA检验规范》由会员分享，可在线阅读，更多相关《PCBA检验规范（50页珍藏版）》请在金锄头文库上搜索。
1、.PCBA检验规范版本：V1.0生效日期：. v.1修订情况表修订历史版本说明作者审核批准生效日期2术语表术语表名称说明. v.目录1.目的(PURPOSE)12.范围(SCOPE)13.名词解释(WORDS EXPLANATION)14.参考文件(REFERENCE DOCUMENT)15. 职责(RESPONSIBILITY) .16. 作业流程及内容(Flow chart and content).17. 修订权限(AUTHORITY OF MODIFICATION)28. (ATTACHMENT).28.1 一(PCBA).48.2 二(机构类).42 8.3 三(其它).52PCBA
2、检验规范1 目的(Purpose)建立产品外观目视检验标准, 使产品检验之判定有所依循, 同时藉由检验资料的回馈分析建立良好的workmanship,防止不良之发生.To establish the standard inspection of product cosmetic for operation to follow, and establish well workmanship by feedback and analyzing the inspection document to void failure.2 范围(Scope)本规范适用于所有产品(含半成品及成品PCBA)的外观目
3、视检验, 包含自行生产制造之PCBA, 委托外包生产制造之PCBA, 以及外购入厂组立或单独包装出货之PCBA等.It fits all product(containing product and PCBA) appearance inspection, including PCBA made by self or by other company and other.3 名词解释(Words explanation)无(None)4 参考文件(Reference document)ANS/IPC-A-610D5 职责(Responsibility)5.1 生产单位(Production u
4、nit):负责产品检验之执行.Be responsible for doing product inspection5.2 质量管理部(Quality unit):负责产品规格之制定及产品品质之抽样检验管制Be responsible for making product specification and controlling the spot check of product quality6 作业流程及内容(Flow chart and content )6.1检验前的准备(preparation for inspecting):检验前须先确认所使用的工具,材料,胶,清洁剂等,是否合乎
5、规定. 检验PCBA 时必须配戴防静电手套或防静电手环, 而成品有外壳部分则不在此限.Before inspecting, be sure of the tool, material, glue, cleanser, etc. Operator should have wrist strap or electrostatic glove for prevention ESD(Electronic static Discharge ), but the finished good with。6.2 若有检验标准未规范的异常现象发生时，不代表该产品允收或拒收，应向值班工程师询问。It is not
6、 means the product accept or reject that the standard of inspection have some abnormal , but should feed back to engineer to confirm.6.3 检验环境要求光线充足,以目视为主,辅以放大镜和卡尺6.4 外观检验项目基准参见一三。The item of cosmetic inspection standard reference Appendix 1 to 3.7 修订权限(Authority of modification)本规范由质量管理部工程师撰写, 经研发单位
7、及生产单位会签, 由质量管理部最高主管核准后实施, 修改程序亦同.This criteria is prepared by Quality unit engineer and signed off with R&D(Research and Develop department )and Production unit, and then approve by Quality manager. Modify procedure as the same above.8 Attachment ( 含记录表单)8.1 一：PCBA Appendix 1: PCBA8.2 二：机构类Appendix
8、2: Mechanical8.3 三：其它Appendix 3: Other预览总表一: PCBA类二: 机构类(Mechanical)三: 其它(Other)1 SMT零件(SMT component)1-1 焊点规格(Soldering SPEC)1-2 焊点异常(Solderingabnormal)1-3 零件损坏(Componentdamage)1-4 点胶(Staking adhesivegluing)1 外壳(Housing)1 标签(Label)2 托架,承座(Chassis)2 Barcode3 铭板(Overlay)3 包装袋(PE bag)4 散热片(Heat sink)4
9、 外箱(Carton)5 绝缘片(Insulator)5 Housing6 螺丝,螺帽,垫片(Screw nut)7 DC series converter 系列成品外观检验标准2 Dip 零件(DIP component)2-1 焊点规格(DIP SPEC)2-2 引脚突出(Lead protrusion)2-3 通孔(PTH)2-4 插件外观(Appearance)2-5 点胶(Adhesive gluing)2-6 DIP高翘(DIP componentlifted)8 Transformer9 Shielding cover 外观检验标准3 PCB3-1 marking3-2 外观(S
10、urface appearance)3-3 焊锡性(Solderability)4 Connector, PIN & 金手指(Golden finger)5 其它(Other)5-1 螺丝(Screw)5-2 跳线(Jump)一: PCBA类1 SMT零件(SMT component)1-1 焊点规格(Soldering SPEC)1-1-1 Chip 零件(Chip component)DefectSide overhang (D) is greater than 50% component termination width (W) or 50% land width (P) whiche
11、ver is less零件偏移D50% W 或D50% P 拒收DefectSide overhang (D) is greater than 50% component termination width (W) or 50% land width (P) whichever is less零件偏移D50% W 或D50% P 拒收DefectAny end overhang (B)零件超出pad 拒收DefectComponent in reserved to lacquer to go to circuit to form a short circuit零件在有保护漆之线路上造成短路拒收
12、AcceptableEnd joint width (C) is minimum 50% of component termination width (W) or 50% land width (P) whichever is less零件焊点宽度C50%W or C50% P 允收AcceptableMaximum fillet height (E) may overhang the lend or extend onto the of the end cap metallization, but not extend further onto the component body锡高超过
13、金属端,但未延伸至零件本体允收DefectSolder fillet extends onto the component body锡延伸到零件本体上拒收DefectMinimum fillet high (F) is less than 25% termination high (H), or fillet high (F) is less than 0.5mmHigh voltage capacitance minimum fillet high (F) is less than 50% termination high (H), or fillet high (F) is less than 0.75mm爬锡高度 F25% H 或 F0.5mm拒收高压电容爬锡高度 F50% H 或 F50% W or 50% P. 拒收
