《韩国灯具标准》由会员分享，可在线阅读，更多相关《韩国灯具标准（10页珍藏版）》请在金锄头文库上搜索。
1、*Korean National Standards* CHAPTER 3 (usual structure) 常用结构 1. The rise in temperature in The Exit lamp must not make trouble标志灯内部温度升高不能影响其在使用市电时的功能。 or do harm against its ability within using power sauce(常用電壓) and voltage. 2.Anti-explosion structure of Anti-explosion Exit lamp must meet standards
2、 arranged by Korean industrial standard of Industrial safety law. 防爆型标志灯的结构要符合韩国行业安全法的行业标准。 3.Set up the Fuse which can protect main power sauce and emergent power sauce from short-circuit. But, Exit lamp being used in seat in a theater(客席lamp) is exceptional. 必须安装保险丝以保证市电以及应急电源在短路时获得保护。 4.The outer
3、 cover of Exit lamp must not be transformed or be changed color through rise-heat. 标志灯外壳在温度升高时不得变色。 5. The outer surface of Exit should be disassembled easily, battery and inner spare parts also should be replaced, repaired and inspected easily. But, water-proof and anti-explosion ones are exception
4、al. 标志灯外壳必须容易拆卸，电池和内部零件必须容易更换、修理和检视。但是防水及防爆灯例外。6.When lighting sauce or lighting tube being changed and inspected, Exit lamps contacting parts should be protected not as to get an electronic shock. 标志灯的连接件安放妥当，以防在更换或检视光源或灯管时发生电击. 7.Using power voltage(使用電壓) should be 2V300V. But, in case its chargin
5、g parts not exposed, available exceeed 300V 适用电压为2V300V, 8.Its structure should be made strong for establishment place. 标志灯的结构强度必须能够承受安装环境。 9.Its structure should be made not getting obstacles itself ability from vibration or shock on transportation. 标志灯的结构要能承受运输过程中的振动和冲击。 10.The inner temperature o
6、f exit lamp should not be risen abnormally, Battery and inner parts have to be in heat-proof management 标志灯的内部温度不能发生非正常升高的情况，电池以及内部零部件要有过热保护装置 11.Distributing wires配線) should not be soldered directly to the battery. 导线不能直接焊在电池上。 12.The power sauce which connecting with using power sauce should be fi
7、t for standard fiber insulation drawing wire and vinyl code. 连接电源的电线必须符合导线和包皮物料的标准 13.The thickness :Drawing wire(引出線)=size: over 0.75m2 others: over 0.5m2引出导线：截面积大于0.75mm2, 其他导线：大于0.5mm2.14. Drawing wire length :over 150mm from wire drawing part. In case that not use drawing wire, should set up a j
8、oining terminal导线长度：引出线要大于150mm, 如果不采用引出线，则要安装接线器。15. Guiding system like a turn and off, voice and similar system can be equipped in the exit lamp. 系统比如开、关和声音，以及类似的系统可以用于标志灯上。16. By receiving via fire alarm equipment or emergency alarm equipment lamp the exit lamp should operate normally on fire. 出
9、口灯主要用于火警。17.18. Automatic returning switch should be equipped. But, floor exit lamp filled under the floor and exit lamp seat in theater(客席exit lamp) dont need.要安装自动归位开关，但是安装在地板下面和剧场座椅上的标志灯不许安装这种开关。.20. Its functioning should be certain, treatment and inspection be on easy, not make noises and obsta
10、cle waves. Besides, its activity should not be influenced by dusts, moisture and insects功能要 ，易于处理和检视，不产生噪声和障碍波 。此外，灰尘、潮气和昆虫不会影响标志灯的工作。21. Repair working and exchanging of spare parts should be on easy. But, water-proof and anti-explosion are exclusive.要易于修理和更换零件。但是防水和防爆灯不受本条限制。22. The parts, may cau
11、se effect on its mechanical function easily by erosion, should be treated as anti-erosion, rust-proof treatment with painting or plating. Terminal and screw etc., have an effect on electronic function, should be made of alloy with copper or endurance-erosion one in same rank as it.容易被腐蚀的零件要作防腐蚀处理，例如
12、油漆或电镀。23 Its distributing wires should have enough currents also, wiring connection should be exact and certain.连接导线要能承受足够强度的电流，导线的连接要可靠。24. Necessary treatment be done so as to prevent misconnection in case of polarity.如果导线的连接要分正负极，则要有明确的标记。25. The attachment of spare parts be done not to make trou
13、ble for its function and not to be untied easily.零件的装配要不影响其功能，而且不易松脱。26. Recharging parts be preserved not to be contacted by human being.放电的部分要仔细处理，不能被人触摸到。27. The inner parts, easily got damage, should have protecting management to avoid making troubles against its structure and function with a ra
14、diation devices of heat. 对于会产生热量的部件，要注意避免对结构和功能产生不良影响。CHAPTER 4 (The structure & function of Parts) 部件的结构和功能1. Switch 开关a. Controlling be easy and certain. Stop point be certain and reasonable要容易控制，工作可靠。b. When the 200%of electronic currents do operate 10,000 times via resistance load at the each co
15、ntacting point with maximum using voltage, its structure and function should not get problems.在以2倍的电流、最大的使用电压在电阻负载下操作1万次，结构与功能都正常。c. The contacting point should be fit for the maximum using current and not be concerned erosion.每个接头都可承受最大的额定电流 rated current? 而且不会锈蚀。d. In case that when you use the lie down and cutting style switch(mercury switch etc.), you should set up a suitable equipment which can returning to original state.当你采用铡刀开关或者水银开关时，必须配备可以使开关归位的装置。2.Signal(表示) lamp 信号灯a. Sockets connection be actual and be attached to being exchanged easily.插座的连接b. Lamps be arranged in parall
