《伺服电机的原理和应用.doc》由会员分享，可在线阅读，更多相关《伺服电机的原理和应用.doc（14页珍藏版）》请在金锄头文库上搜索。
1、伺服电机原理和应用Servomotors are available as AC or DC motors. Early servomotors were generally DC motors because the only type of control for large currents was through SCRs for many years. As transistors became capable of controlling larger currents and switching the large currents at higher frequencies,
2、the AC servomotor became used more often. Early servomotors were specifically designed for servo amplifiers. Today a class of motors is designed for applica-tions that may use a servo amplifier or a variable-frequency controller, which means that a motor may be used in a servo system in one applicat
3、ion, and used in a variable-frequency drive in another application. Some companies also call any closed-loop system that does not use a stepper motor a servo system, so it is possible for a simple AC induction motor that is connected to a velocity controller to be called a servomotor.Some changes th
4、at must be made to any motor that is designed as a servomotor in-cludes the ability to operate at a range of speeds without overheating, the ability to operate at zero speed and retain sufficient torque to hold a load in position, and the ability to operate at very low speeds for long periods of tim
5、e without overheating. Older-type motors have cooling fans that are connected directly to the motor shaft. When the motor runs at slow speed, the fan does not move enough air to cool the motor. Newer motors have a separate fan mounted so it will provide optimum cooling air. This fan is powered by a
6、con-stant voltage source so that it will turn at maximum RPM at all times regardless of the speed of the servomotor. One of the most usable types of motors in servo systems is the permanent magnet (PM) type motor. The voltage for the field winding of the permanent magnet type motor can be AC voltage
7、 or DC voltage. The permanent magnet-type motor is similar to other PM type motors presented previously. Figure 11-83 shows a cutaway picture of a PM motor and Fig. 11-84 shows a cutaway diagram of a PM motor. From the picture and diagram you can see the housing, rotor and stator all look very simil
8、ar to the previous type PM motors. The major difference with this type of motor is that it may have gear reduction to be able to move larger loads quickly from a stand still position. This type of PM motor also has an encoder or resolver built into the motor housing. This ensures that the device wil
9、l accurately indicate the position or velocity of the motor shaft. FIGURE 11-83 Typical PM servomotors.FIGURE 11-84 Cutaway picture of a permanent magnet servomotor.11.11.5.1 Brushless Servomotors The brushless servomotor is designed to operate without brushes. This means that the commutation that t
10、he brushes provided must now be provided electronically. Electronic commutation is provided by switching transistors on and off at appropriate times. Figure 11-85 shows three examples of the voltage and current waveforms that are sent to the brushless servomotor. Figure 11-86 shows an example of the
11、 three windings of the brushless servomotor. The main point about the brushless servomo-tor is that it can be powered by either ac voltage or dc voltage.Figure 11-85 shows three types of voltage waveforms that can be used to power the brushless servomotor. Figure ll-85a shows a trapezoidal EMF (volt
12、age) input and a square wave current input. Figure ll-85b shows a sinusoidal waveform for the input voltage and a square wave current waveform. Figure ll-85c shows a sinusoidal input waveform and a sinusoidal current waveform. The sinusoidal input and sinusoidal current waveform are the most popular
13、 voltage supplies for the brushless servomotor.Figure 11-86 shows three sets of transistors that are similar to the transistors in the output stage of the variable-frequency drive. In Fig. ll-86a the transistors are connected to the three windings of the motor in a similar manner as in the variable-
14、frequency drive. In Fig. 1 l-86b the diagram of the waveforms for the output of the transistors is shown as three separate sinusoidal waves. The waveforms for the control circuit for the base of each transis-tor are shown in Fig. ll-86c. Figure ll-86d shows the back EMF for the drive waveforms.FIGUR
15、E 11-85 (a) Trap-ezoidal input voltage and square wave current wave-forms. (b) Sinusoidal in-put voltage and sinusoidal voltage and square wave output voltage wave-forms. (c) Sinusoidal in-put voltage and sinusoi-dal current waveforms. This has become the most popular type of brushless servomotor co
16、ntrol.Servomotor Controllers Servomotor controllers have become more than just amplifiers for a servomotor. Today servomotor controllers must be able to make a number of decisions and provide a means to receive signals from external sensors and controls in the system, and send signals to host controllers and PLCs that may interface with the servo system. Figure 11-87 shows a picture of several servomotors and their amplifiers. The components in th
