《techenglish石油天然气工业科技英语培训教材》由会员分享，可在线阅读，更多相关《techenglish石油天然气工业科技英语培训教材（100页珍藏版）》请在金锄头文库上搜索。
1、FIRST SOLUTIONS LIMITED9About This BookWhat is it?This is a specially tailored technical English textbook. It is made up of the following:1. Aim and objectiveRequirement or expectations from the compiler. The trainees are free to come up with their expectations, or suggestions.2. GlossaryMore than 5
2、000 commonly used words or phrases are garnered and sorted out by the inherent logic rather than alphabetically. They will be explained or illustrated lively and vividly. 3. ReadingThree to five pieces of relevant articles are included in each chapter. A huge resource of manuals, textbooks from our
3、library are always available for the trainees.4. ListeningThe listening materials are as below:A. A/V materials accumulated since 1993 when Nan Hai Training Center (the predecessor of FSL) was setup.B. Presentation by or conversation with our foreign experts. 5. WritingUnder the guidance of instruct
4、ors, the trainees will learn how to write log book, handover notes, PO, daily reports, etc.6. Assessment and commentA. The trainees will make presentations.B. The trainees will do a written test.C. The trainees will make a self-assessment.D. Comment, criticism or suggestions to the instructor.For wh
5、om?It is for the people who are or will be working in the oil/gas industry. By whom ?This book was compiled by experienced experts, engineers who worked in the fields of Chevron, Phillips, JHN, Statoil, BP for years.How to conduct?A. In-depth, lively and vivid explanations or illustrations from our
6、instructors. B.Application-oriented.C.The trainees will see, touch and use our equipment in the workshop or library to understand, use and memorize the words or phrases.After the course?The trainees will not only have a good command of the words, but also will be very conversant with essential knowl
7、edge for their future job.CONTENTChapterPage1.0 General1.1 Aim and objectives71.2 Glossary1.2.1 Overview81.2.2 Facility81.2.3 Organization81.2.4 Transportation91.2.5 Miscellaneous91.3 Reading 1.3.1 Introduction materials of offshore oil industry111.4 Listening121.5 Writing121.6 Assessment and commen
8、t132.0 HES2.1 Aim and objectives142.2 Glossary2.2.1 Qualification and certificate152.2.2 Personnel transportation152.2.3 New arrivals152.2.4 Personal protective equipment152.2.5 Working system162.2.6 Undesirable events172.2.7 Pollution172.2.8 Health and medical172.2.9 Warning signs182.2.10 Emergency
9、 response182.3 Reading 2.3.1 Work permit202.3.2 Scaffolding212.3.3 Risk/hazard identification222.3.4 Basic rigging and slinging232.3.5 Environment control272.4 Listening 302.5 Writing302.6 Assessment and comment313.0 Crude oil and Gas Production.3.1 Aim and objectives323.2 Glossary3.2.1 Petrol chemi
10、stry and physics333.2.2 Symbols and abbreviations333.2.3 Well control343.2.4 Separation343.2.5 Sampling and analysis343.2.6 Secondary recovery343.2.7 Ancillary and utility343.2.8 Miscellaneous353.3 Reading3.3.1 Introduction363.3.2 Crude Oil Degassing373.3.3 Principles of Operation373.4 Listening383.
11、5 Writing383.6 Assessment and comment394.0 Mechanical Engineering4.1 Aim and objectives414.2 Glossary4.2.1 Basic hand tools424.2.2 Engineering measurement and drawing424.2.3 Engineering Materials and properties434.2.4 Lubrication and hydraulic434.2.5 Fastening devices434.2.6 Gaskets, packing, seals
12、and bearings444.2.7 Manual valves444.2.8 Belt drives, shaft coupling and alignment444.2.9 Pumps and compressors444.2.10 Offshore crane454.2.11 Internal Combustion engines454.2.12 Miscellaneous464.3 Reading4.3.1 Principle of Operation474.3.2 Combustible Engine484.3.3 Positive Displacement Pump494.4 L
13、istening504.5 Writing.504.6 Assessment and comment515.0 Electrical Engineering5.1 Aim and objectives525.2 Glossary5.2.1 Electric theory535.2.2 Electrical tools535.2.3 Power generation535.2.4 Switchgear and power distribution535.2.5 Electrical equipment535.2.6 Basic Electrical parts545.2.7 Battery an
14、d UPS545.2.8 Electronics545.2.9 Electrical safety545.3 Reading5.3.1 Poly Phase Transmission555.3.2 Battery565.3.3 Induction Motors585.4 Listening595.5 Writing595.6 Assessment and comment606.0 Instrumentation And Control6.1 Aim and objectives616.2 Glossary.6.2.1 Theory626.2.2 Instrumentation tools626
15、.2.3 Signal and Measurement626.2.4 Controller636.2.5 Control device636.2.6 Tubing and fitting636.2.7 PLC and DCS636.2.8 F/G detection and protection646.2.9 Miscellaneous646.3 Reading6.3.1 Process Control656.3.2 The Differential Pressure Cell666.3.3 Flapper Nozzle System676.3.4 Measurement686.4 Listening696.5 Writing 696.6 Assessment and comment.707.0 IT and Telecom7.1 Aim and ob
