《测距仪使用说明.doc》由会员分享，可在线阅读，更多相关《测距仪使用说明.doc（3页珍藏版）》请在金锄头文库上搜索。
1、Forestry pro measurement procedure guideTo start :开始1,press POWER button to turn on按电源键POWER打开2,confirm your mode with the internal display (default is “last used” setting) 确认你的模式与内部显示(默认是“最后的使用“设置)3,Set your desired mode and start measuring设置你想要的模式,开始测量Mode setting：模式设置Target priority modes目标优先模式1、
2、press and hold MODE button,then press and hold POWER button within 0.5 second. 按下并保持住模式按钮，然后同时按住电源按钮在0.5秒之内2、Continue to press and hold both buttons(more than 2 seconds)until first target priority mode and distant target priority mode are switched. 继续同时按住两个按钮(超过2秒),直到第一个目标优先模式和遥远的目标优先模式切换。3、if the b
3、utton is not pressed within 0.5 second ,the display unitwill be switched. 如果按钮不是压在0.5秒之内,显示单元将切换。Dst:Distant priority mode (factory setting) 遥远的优先模式(工厂设置)1st:first priority mode第一优先模式Measurement modes测量模式Press and release MODE button. 按下和释放模式按钮Measurement mode changes in the order of 1 (Act)to 6 (Ho
4、r)as shown below. 测量模式变化的顺序1(Act)到6(Hor)如下所示。Holding down MODE button longer switches the display unit. 按住模式MODE按钮开关的显示装置1.Act:linear distance直线距离2.Hor(solid):horizontal distance水平距离3.Hgt(solid):height from horizontal高度4.Ang: angle (degrees)from horizontal角度5.Hgt(blinking):vertical separation(height
5、 between two points) Hgt闪动为垂直分离（两点之间高度）测试模式6.Hor(blinking):three-point measurement (height between two points)三分测量One-point(Act/Hor/Hgt/Ang)measurement单点测量(measurement order:1-2-3-4-2,then repeat)测量顺序从1-2-3-4-2，然后重复Target point目标点Internal display(“linear distance mode”)内部展示，直线距离模式(display will be di
6、fferent depending on the setting mode.)显示的不同取决模式1.set your desired mode.设置你想要的模式2.Aim at the target.瞄准3.Press POWER button to measure， keeping the button pressed allows continuous measurement of up to 20 seconds. 按电源按钮保持20秒来衡量4.Results display example of each mode结果显示每个模式的例子（1）Act :Linear distance m
7、ode直线距离模式（2）Hor: horizontal distance mode水平距离模式（3）Ang:Angle mode角度模式（4）Hgt: height mode高度模式Power turns off 30 seconds after the last operation.停止操作30秒后，电源关闭。External display reading instructions外部显示阅读指令（Actual external display image）实际外部显示图像All data below is displayed simultaneously同时显示下面数据Act (line
8、ar distance)直线距离Hor (horizontal distance)水平距离Hgt(height from horizontal)高度Ang (angle from horizontal)角度Measuring vertical separation (height between two points) 测量垂直分离(高度两点之间)(measurement order :1-2-3-4-5-6-7-2,then repeat) (测量顺序:1-2-3-4-5-6-7-2,然后重复)1st target point第一目标点2nd target point第二目标点Interna
9、l display内部展示1、Display when the vertical separation (height between two points)mode is selected显示垂直分离(高度两点之间)模式被选中2、Aiming at the 1st point瞄准第一点3、Press POWER button to measure 按电源按钮来衡量4、Display of the height from horizontal level of 1st point显示从水平线到第一点的高度5、Aiming at the 2nd target point针对第二点目标6、Pres
10、s POWER button to measure按电源按钮来衡量7、Display of the vertical separation (height between two points)显示两点之间高度（This symbol indicates the display is blinking显示器闪烁符号）External display reading instructions外部显示阅读指令After the measurement of 1st target point (actual external display image)After the measurement o
11、f 2st target point(display of the vertical height between two points)(actual external display image)Three point measurement (height between two points)三分测量（高度两点之间）(measurement order :1-2-3-4-5-6-7-8-2,then repeat)1st target point2nd target point3rd target pointWhen measuring 2nd and 3rd points pleas
12、e note that angles should be between -75and +75from the horizontal level .if measurement fails ,the angle is beyond 75当测量第2和第3点请注意,-75之间的角度应该和+ 75的水平。如果测量失败,75角超出Internal display1、Display when three point measurement mode is selected显示当三个点测量模式被选中2、Aiming at the 1st point .瞄准第一点3、Press POWER button t
13、o measure按电源按钮来衡量4、Display of the horizontal distance to the 1st point.显示第一点水平距离5、Aiming at the 2nd target point.瞄准第二点6、Press POWER button to measure按电源按钮来衡量7、Display of the vertical separation (height from horizontal level to 2nd point). 显示垂直分离(高度从水平到第二点)。8、Aiming at the 3rd target point.瞄准第三点9、Pre
14、ss POWER button to measure按电源按钮来衡量10、Display of the vertical separation (height between 2nd and 3rd points) 显示垂直分离(第2和第3点之间的高度)External display reding instructionsAfter the measurement of 1st target point (actual external display image)After the measurement of 2st target pointdisplay of the vertical separation(height from horizontal level to 2nd points)(actual external display image)After the measurement of 3rd target point (display of the vertical height between 2nd and 3rd points)(actual external display image)
