《声发射操作步骤》由会员分享，可在线阅读，更多相关《声发射操作步骤（23页珍藏版）》请在金锄头文库上搜索。
1、打开软件界面。|tVallen Control Panel R2008. 0915口叵冈| Normal Use TR VisualClass Utilities Veri Utilities AllSB EALARM留Acquisitio. VisualAEAlarmMan agerHelp on VisualAEHelp onAcquisiti onHelp on AEUtilitiesAcquisition32:AMSY-5: Data acquisition program:Aquires AE plus TR.-data (if optional TR modules are ins
2、talled). Double click on the icon to start this programThis product is licensed for:CST - Beijing Crahesion Science .Trade Co. Ltd.Beijing, P.R. ChinaDemonstration Unit not for commercial useTime limited Expire Date:(349 days left)盘卫dipZIl & AboutI Hide | Close 首先对硕件进行测试：双击Acquisitions?,首先会对仪器的硬件进行测
3、试，查看其状态 是否完好（如图2所示）Vallen Acquisition32 for A1SY-5 R2008. 0915The Acoustic Emission CompanyvallensusuemeVallen Acqutsition32 for AMSY-5 R2008.0915:Please wait while hardware detection in progress.Copyright 1986-2008 by Vallen Systeme GmbH. All rights reserved.匚回?仪器硕件自检后出现如图3所示的界面 Hardvare Detection
4、Results & Channel ConfigurationBelovj you will find the results of the hardvjare detection.The upper list shov/s the AE channal巳 the lover list the parametric channels detectedResults of AE channel detection:Edit ModeView ModeMore.Chan. HVU Exist Rev. Squarer FB-HP Input devicePulser func. DC Preamp
5、. ID Sensor 八列 5 T 01.03.3 YesR20.07 YesHP-HiAC Input100KNoneS3 5T 01.03.b YesR20.07 YesHP-HiAC Input100KNone列701.04.a YesR20.07 YesHP-HiAC Input100KNone錮301.04.b YesR20.07 YesHP-HiAC Input100KNone錮901.05.a YesR20.07 YesHP-HiAC Input100KNone錮10Ol.OS.b YesR20.07 YesHP-HiAC Input100KNone聖 11 01.06.3 Y
6、es R20.07 Yes HP-Hi AC Input100K Noneil 12 01.06.b Yes R20.07 Yes HP-Hi AC Input100K NoneResults of parametric channel detection:Chan.ExistNameStatus/ 0YesPaOOK./ 1YesPalOK.IHelp IILog file.Retry.ConfirmCancel图3点击Edit Mode,在Input deviceJ中选择所用的探头型号（如图4所示）。Hardware Detection Results & Channel Configur
7、ationBgIov you will find the results of the hardvare detGcbon.The upper list shows the AE channel気 the lov/er list the porometric channels detectedResults of AE channel detection:| Edit Mod View 啦厂 More.Results of parametric channel detection:Edit Mode: Specify a logical cha nrwl number (colum n Cha
8、 n. end an in put device for each physical hard wore channel. Logical dionnel numbers must be unique Quick copy: To copy cells from upper line, press,+, in the cell belowFor logical channel numbers in ascending order, also use ”4” within the channel cellChan.HWInput devicePulser fu ncDC Preamp. IDSe
9、nsor IDStatusA701.04.a岡5|Nonno chngQ.801.04.bAC Input100KNonno chwnge.901.05.9AC InputOlOOKNoneno change.1001.05.bACInput100KNoneno change.1101.06.aAC Input 100KNoneno change.12Ol.Ob.bAC input 100KNoneno change.*点击Confirm确认设置及检测结果，将出现如图5所示界面以及重新进行仪器硕件自检, 如图6所示。图5仪器硕件再次自检后的结杲如图7所示Hardvare Detection R
10、esults k Channel ConfigurationBelow you will find the resjlts of the hardv/ore detecti on .The upper list shows the AE chonn els, the lower list the parametric channels detectedResults of AE channol detection:Edit ModeView NodeMore.Chon.HWExistRev. Squorer FB HP Input devicePulser fu ncDC Preomp. ID
11、 Sensor 入fisl 1 TOl.Ol.a YesR20.07 YesHP-HiAC Input100KNone愆2T01.01.b YesR20.07 YesHP-HiAC Input100KNone&21 301.02.a YesR20.07 YesHP-HiAC Input100KNone世| 4O1.02.b YesR20.07 YesHP-HiAC lnput100KNone匪1 5T01.03.3 YesR20.07 YesHP-HiAC lnput100KNone匪1 6T01.03.b YesR20.07 YesHP-HiAC Input100KNone愆701.04.a
12、 YesR20.07 YesHP-HiAC Input100KNone跚801.04.5 YesR20.07 YesHP-HiAC InputOlOOKNone更1 9Ol.OS.a YesR20.07 YesHP-HiAC InDUtlOOKNoneVIlResults of parametric channel detection:Chan.ExistNameStotusYesPaOOK.YesPalOK.图7点击“OK”进行卞一步操作设置，即为检测或者建立存储文件以及其存储的路径。如 图8、9所示。口ftecent文拌名龜）：vfillan vacv打开文件类型d）：Villen Acq
13、uisition取消帮助elect or enter acquisition file萱披范a（I）我的文档 我的电痫 屯网上邻居 己北航点击“打开”，出现如图10所示界面。图11点击“Yes”后，文件己建立，将出现如图12所示界面。Select Acquisition SettingsA new acquisition file has been created Please define the acquisition settings to be used:Click on HUbraryn to select user-defined settings.Click on Browse” to select another VAC file and copy the settings from.Click on Factory Defaults11 to use applicationspecific predefined settings.Library.Browse.Factory Defaults.图12点击“Factory DefaultsS将出现如图13所示的界面。图13 点击“OK7将出现图14所示界面。
