《磁力研磨机说明书.doc》由会员分享，可在线阅读，更多相关《磁力研磨机说明书.doc（9页珍藏版）》请在金锄头文库上搜索。
1、东莞市顺佳研磨科技有限公司顺佳研磨科技有限公司磁力精密研磨机PRECISION MAGNETIC GRINDERhttp:/机械原理简介Mechanic Principle利用神奇磁场力量传导不锈钢针磨材产生加速旋转动作，高效率达到精密研磨去除毛边和抛光洗净效果With the use of the magical force of magnetic field, making the stainless steel pins rotate very fast, to de-burr, polish and clean the workpieces high-effectively and p
2、recisely.1、特点 Features1) 卓越快速去除毛边能力，细小内孔、内管、夹缝死角均可高效研磨，绝不变形及伤表面，不影响精度。Have excellent ability of fast de-burring, high efficiently grinding small inner holes, inner pipes, crevices, etc. Make NO damage to the surface of workpieces, and DO NOT affect the accuracy of workpieces.2) 加工速度快，一次315分钟即可完成，可在机
3、器运转中替换工件。Fast grinding or polishing, only 315 minutes is needed for each time.Workpieces can be changed during the machine running.3) 操作方面简单，成本低，无污染，不锈钢针为永久性磨材。Simple and convenient operation, low cost, no pollution. The stainless steel pins are permanent abrasives.2、用途 Application金饰业打磨洗净工作，成品表面抛光处理
4、，去除氧化薄膜工作，锈蚀去除处理，电镀或喷漆前处理，烧结痕迹处理，零件残磁去除。 Use in metal industry for Gringding, cleaning, polishing surface of workpiece, removing layer of oxide on the workpiece, derusting, processing before plating or painting, processing the marks of sintering, and demagnetizing the workpiece.3、说明 Description 1)研磨
5、速度快，平均一次研磨时间约315分钟，替换工件快，可在机器运转过程中替换零件。 Grinding quickly, it only takes 315 minutes for each time on average.Easy and fast changing the workpieces, the workpieces can be changed during the machine running.2)操作简单，绝对安全，完全免技术，一人可操作多台机器。 Simple operation, absolute safety. One person can operate multiple
6、 machines.3)成本低，不锈钢针为永久性磨材，消耗极低，唯一的耗材为研磨液。无污染，研磨液含95%水分，故无毒性及发生火灾之虑。 Low cost, the stainless steel pins are permanent abrasives. The only consumable item is Grinding (Brightening) Fluid. No pollution. The grinding (brightening) fluid contains 95% moisture, and is non-toxic; you can have no worry abo
7、ut fire on it.4)研磨完成后，工件好处理，可用筛网、筛桶或磁铁，轻易将工件和不锈钢针分开。 The workpieces can be easily dealt with after grinding. Can use a sieve mesh, sieve drum or magnet to easily separate the workpieces from the pins4、安装环境 Installing Environment1)无水滴、蒸汽、灰尘及油性灰尘之场所。 Place WITHOUT water drops, vapor, dust or oily dust
8、.2)无腐蚀、易燃性之气体、液体。Place WITHOUT corrosive, flammable liquid or gas.3)无漂浮性的尘埃及金属微粒。 Place WITHOUT floating dirt and metal particle.4)紧固无振动之场所。 Place of no vibration.5、操作顺序1)将机器连接在有可靠接地的标准电源中。各型号对电源要求如下：型号电源要求SJ-6603相380V，50/60HZ，13ASJ-6503相380V，50/60HZ，13ASJ-645单相220V，50/60HZ，13ASJ-635单相220V，50/60HZ，1
9、3ASJ-628单相220V，50/60HZ，13AConnect the machine to the standard power supply with reliable ground lead. The power supply for each model is as below.MODELPOWER SUPPLYSJ-6603 Phase 380V，50/60HZ，13ASJ-6503 Phase 380V，50/60HZ，13ASJ-645Single Phase 220V，50/60HZ，13ASJ-635Single Phase 220V，50/60HZ，13ASJ-628S
10、ingle Phase 220V，50/60HZ，13A2)将放有适量工件及研磨材料之塑料质容器放在研磨槽中间位置，开启电源(ON)，设定总研磨时间TOTAL TIMER(H小时.M分。S秒)及正反转时间REV/FWD TIMER、设置工作速度SPEED SET(0-10V模拟速度)，9V等于1400转左右。 Put the plastic grinding container (e.g.a tub) with proper amount of workpieces and abrasives in the middle of the grinding trough, turn on the
11、power and set the total time (Hour. Minutes. Second), the REV/FWD time, and the working speed (010V, 9V=1400 r/min).3)启动运行按钮START，机器开始工作。 Press the “START” Key, and the machine starts working.4)工作在设定时间完成后，应再次启动机器，拿走研磨桶进行清洗，然后按STOP按钮停止工作。(原因是工件在机器磁场运转中才能消除剩磁) After work finishing, should start again
12、the machine and take away the grinding tub from the trough to clean the workpieces, and then stop the machine. (As the workpieces can only be demagnetized during the machine running.)5)用分选筛将不锈钢针分选后，放回桶内以便下次使用。 Separate the stainless steel pins with a sieve. The pins can be used again.6、使用方法 Method o
13、f Usage1)使用塑料质容器，以免损坏工件。 Use a plastic container, (e.g. a plastic tub.) to avoid damaging the workpieces.2)放入适量的不锈钢针，研磨液，水和工件进行研磨或者抛光。以下数据供参考：型号每次研磨时需用的不锈钢针、研磨液、水和工件的分量速度设定(仅供参考)SJ-660钢针0.4以下的约1000克，若0.5以上的钢针要用约2000克；研磨液60毫升；水6公斤；工件：非导磁材料610千克，导磁材料14千克。9V(约1400r/min)SJ-650钢针15002000克；研磨液4060毫升；水56公斤
14、；工件：非导磁材料58千克，导磁材料1-2.5千克。9V(约1400r/min)SJ-645钢针约1200克，研磨液2040毫升；水35公斤；工件非导磁材料36千克，导磁材料1-2千克。9V(约1400r/min)SJ-635钢针约700克；研磨液2040毫升；水24公斤；工件：非导磁材料13千克，导磁材料1千克。9V(约1400r/min)研磨工件时导磁材料分量为非导磁材料分量的1/3。工件超分量研磨，机器如有损坏本公司概不负责。 Put appropriate amount of stainless steel pins, grinding fluid, water and workpie
15、ces into the tub to grind or polish. The following amount is for reference.MODLEThe amount of pins, grinding fluid, water and workpieces to be used each time Speed Setting (Only for reference)SJ-660Pins 0.4, use about 1000 grams, if the pins 0.5, use about 2000 grams; grinding fluid 60ml, water 6 kg, workpieces non-magnetic material 610 kg.,magnetic materials 1-4kg9V(about 1400r/min)SJ-650Pins 15002000 grams; grinding fluid 4060ml, water 56 kg, workpieces non-magnetic material 58 kg.,magnetic materials 1-2.5kg
