《红外温度传感器OTP-538U.doc》由会员分享，可在线阅读，更多相关《红外温度传感器OTP-538U.doc（7页珍藏版）》请在金锄头文库上搜索。
1、深圳永盟电子邬先生 152.2017.9727Thermopile SensorOTP-538URevision Date: 2009/04/16 IntroductionThe OTP-538U is a thermopile sensor in classic TO-46 housing. The sensor is composed of 116 elements of thermocouple in series on a floating micro-membrane having an active diameter of 545 m and with blacken surfac
2、e to absorb the incident thermal infrared radiation, which induces a voltage response at output terminals. The sensor chip is fabricated by a unique front-surface bulk micromachining technology, which result in smaller size and faster to response ambient temperature change.The IR window is a bandpas
3、s filter having its 50% cut-on wavelength at 5 m, and cut-down at 14m. The sensor responses proportionally to the incident IR radiation and has a constant signal response up to its cut-off frequency, which is limited by the sensor thermal time constant of tens millisecond range.The OTP-538U thermopi
4、le sensor provides nearly Johnson-noise-limited performance, which canbe calculated by its ohmic series resistance. A thermistor element, with a lead connected to ground, is also provided inside the TO package for ambient temperature reference.Features Non-contact temperature detection
5、48698; Voltage output, easy to take signal Zero power consumption Wide detection temperature range Applications Medical Application: Ear thermometers Home Facility: Microwave oven, Hair dryer, Safety system, Home security, Refrigerator & Airconditioner
6、8; Industry Application: Process monitor and controller, Infrared non-contact thermometers Automobile Application: Thermal sensing systemTable of Contents1 General Characteristics1.1 Absolute Maximum Ratings1.2 Handling Guidelines2 Device Characteristics2.1 Device Descriptions2.2 Sensor Ch
7、aracteristics2.3 Signal Output Characteristics2.4 Frequency Response2.5 Thermistor Characteristics2.6 Optical Characteristics2.7 Filter Characteristics2.8 Mechanic Drawing and Pin Assignment3 Liability StatementList of FiguresFigure 1: Typical output voltage versus object temperature with sensor at
8、25 CFigure 2: Frequency responseFigure 3: Field of view curveFigure 4: Typical spectral transmittance curveFigure 5: Mechanical drawing and pin assignmentList of TablesTable 1: Absolute maximum ratingsTable 2: Device characteristicsTable 3: Thermopile sensor characteristicsTable 4: Typical numerical
9、 data of Thermopiles output voltage (sensor at 25 C)Table 5: Thermistor informationTable 6: Tabulated thermistor dataTable 7: Optical characteristicsTable 8: Filter parameters1. General Characteristics1.1 Absolute Maximum Rating1.2 Handling Guidelines Stresses above the absolute maximum ra
10、tings may cause damages to the device. Do not expose the sensor to aggressive detergents such as Freon, Trichloroethylene, etc. Avoid touching or cleaning of the window. If necessary, do cleaning only very carefully with alcohol andcotton swab. Hand soldering and wave s
11、oldering may be applied by a maximum temperature of 260 C for a dwell timeless than 10 s. Reflow soldering is not recommended.2. Device Characteristics2.1 Device DescriptionsThe materials of OTP-538U are lead-free and fully complied with the RoHS regulations.2.2 Sensor CharacteristicsNotes: * All op
12、tical performances are measured at 1 Hz chopper frequency using a blackbodyradiator of 500K temperature with filtered spectrum ranging from 5 to 14 m.Distance between packaged thermopile and blackbody is 11cm.2.3 Signal Output Characteristics3. Liability StatementThe contents of this document are su
13、bject to change without notice and customers should consult withOriental System Technology (OST) sales representatives before ordering. Customers considering the use ofOST thermopile devices in applications where failure may cause personal injury or property damage, or whereextremely high levels of
14、reliability are demanded, are requested to discuss their concerns with OST salesrepresentatives before such use. The Companys responsibility for damages will be limited to the repair orreplacement of defective product. As with any semiconductor device, thermopile sensors or modules have acertain inherent rate of failure. To protect against injury, damage or loss from such failures, customers areadvised to incorporate appropriate safety design measures into their product.
