《模糊PID控制器的设计和仿真——设计步骤(修改)》由会员分享，可在线阅读，更多相关《模糊PID控制器的设计和仿真——设计步骤(修改)（4页珍藏版）》请在金锄头文库上搜索。
1、 .wd.模糊PID控制器的设计与仿真设计模糊PID控制器时，首先要将准确量转换为模糊量，并且要把转换后的模糊量映射到模糊控制论域当中，这个过程就是准确量模糊化的过程。模糊化的主要功能就是将输入量准确值转换成为一个模糊变量的值，最终形成一个模糊集合。 本次设计系统的准确量包括以下变量：变化量e ，变化量的变化速率ec 还有参数整定过程中的输出量KP，KD，KI，在设计模糊PID 的过程中，需要将这些准确量转换成为模糊论域上的模糊值。本系统的误差与误差变化率的模糊论域与 基本论域为：E=-6,-4,-2,0,2,4,6;Ec=-6,-4,-2,0,2,4,6。模糊PID控制器的设计选用二维模糊控
2、制器。以给定值的偏差e和偏差变化ec为输入；KP，KD，KI为输出的自适应模糊PID控制器，见图1。图1模糊PID控制器1模糊变量选取 输入变量E和EC的模糊化将一定范围( 基本论域)的输入变量映射到离散区间(论域)需要先验知识来确定输入变量的范围。就本系统而言，设置语言变量取七个，分别为 NB，NM，NS，ZO，PS，PM，PB。(2) 语言变量及隶属函数根据控制要求，对各个输入，输出变量作如下划定：e，ec论域：-6，-5，-4，-3，-2，-1，0，1，2，3，4，5，6KP，KD，KI论域：-6，-5，-4，-3，-2，-1，0，1，2，3，4，5，6应用模糊合成推理PID参数的整定算
3、法。第k个采样时间的整定为式中为经典PID控制器的初始参数。设置输入变量隶属度函数如图2所示，输出变量隶属度函数如图3所示。图2 输入变量隶属度函图3 输出变量隶属度函（3） 编辑模糊规那么库根据以上各输出参数的模糊规那么表，可以归纳出49条控制逻辑规那么，具体的控制规那么如下所示：1. If (e is NB) and (ec is NB) then (kp is NB)(ki is PB)(kd is NS)(1)2. If (e is NB) and (ec is NM) then (kp is NB)(ki is PB)(kd is PS)(1)3. If (e is NB) and
4、(ec is NS) then (kp is NM)(ki is PM)(kd is PB)(1)4. If (e is NB) and (ec is ZO) then (kp is NM)(ki is PM)(kd is PB)(1)5. If (e is NB) and (ec is PS) then (kp is NS)(ki is PS)(kd is PB)(1)6. If (e is NB) and (ec is PM) then (kp is ZO)(ki is ZO)(kd is PM)(1)7. If (e is NB) and (ec is PB) then (kp is Z
5、O)(ki is ZO)(kd is NS)(1)8. If (e is NM) and (ec is NB) then (kp is NB)(ki is PB)(kd is NS)(1)9. If (e is NM) and (ec is NM) then (kp is NB)(ki is PB)(kd is PS)(1)10. If (e is NM) and (ec is NS) then (kp is NM)(ki is PM)(kd is PB)(1)11. If (e is NM) and (ec is ZO) then (kp is NS)(ki is PS)(kd is PM)
6、(1)12. If (e is NM) and (ec is PS) then (kp is NS)(ki is PS)(kd is PM)(1)13. If (e is NM) and (ec is PM) then (kp is ZO)(ki is ZO)(kd is PS)(1)14. If (e is NM) and (ec is PB) then (kp is PS)(ki is ZO)(kd is ZO)(1)15. If (e is NS) and (ec is NB) then (kp is NM)(ki is PB)(kd is ZO)(1)16. If (e is NS)
7、and (ec is NM) then (kp is NM)(ki is PM)(kd is PS)(1)17. If (e is NS) and (ec is NS) then (kp is NM)(ki is PS)(kd is PM)(1)18. If (e is NS) and (ec is ZO) then (kp is NS)(ki is PS)(kd is PM)(1)19. If (e is NS) and (ec is PS) then (kp is ZO)(ki is ZO)(kd is PS)(1)20. If (e is NS) and (ec is PM) then
8、(kp is PS)(ki is NS)(kd is PS)(1)21. If (e is NS) and (ec is PB) then (kp is PS)(ki is NS)(kd is ZO)(1)22. If (e is ZO) and (ec is NB) then (kp is NM)(ki is PM)(kd is ZO)(1)23. If (e is ZO) and (ec is NM) then (kp is NM)(ki is PM)(kd is PS)(1)24. If (e is ZO) and (ec is NS) then (kp is NS)(ki is PS)
9、(kd is PS)(1)25. If (e is ZO) and (ec is ZO) then (kp is ZO)(ki is ZO)(kd is PS)(1)26. If (e is ZO) and (ec is PS) then (kp is PS)(ki is NS)(kd is PS)(1)27. If (e is ZO) and (ec is PM) then (kp is PM)(ki is NM)(kd is PS)(1)28. If (e is ZO) and (ec is PB) then (kp is PM)(ki is NM)(kd is ZO)(1)29. If
10、(e is PS) and (ec is NB) then (kp is NS)(ki is PM)(kd is ZO)(1)30. If (e is PS) and (ec is NM) then (kp is NS)(ki is PS)(kd is ZO)(1)31. If (e is PS) and (ec is NS) then (kp is ZO)(ki is ZO)(kd is ZO)(1)32. If (e is PS) and (ec is ZO) then (kp is PS)(ki is NS)(kd is ZO)(1)33. If (e is PS) and (ec is
11、 PS) then (kp is PS)(ki is NS)(kd is ZO)(1)34. If (e is PS) and (ec is PM) then (kp is PM)(ki is NM)(kd is ZO)(1)35. If (e is PS) and (ec is PB) then (kp is PM)(ki is NB)(kd is ZO)(1)36. If (e is PM) and (ec is NB) then (kp is NS)(ki is ZO)(kd is NB)(1)37. If (e is PM) and (ec is NM) then (kp is ZO)
12、(ki is ZO)(kd is PS)(1)38. If (e is PM) and (ec is NS) then (kp is PS)(ki is NS)(kd is NS)(1)39. If (e is PM) and (ec is ZO) then (kp is PM)(ki is NS)(kd is NS)(1)40. If (e is PM) and (ec is PS) then (kp is PM)(ki is NM)(kd is NS)(1)41. If (e is PM) and (ec is PM) then (kp is PM)(ki is NB)(kd is NS)
13、(1)42. If (e is PM) and (ec is PB) then (kp is PB)(ki is NB)(kd is NB)(1)43. If (e is PB) and (ec is NB) then (kp is ZO)(ki is ZO)(kd is NB)(1)44. If (e is PB) and (ec is NM) then (kp is ZO)(ki is ZO)(kd is NM)(1)45. If (e is PB) and (ec is NS) then (kp is PM)(ki is NS)(kd is NM)(1)46. If (e is PB)
14、and (ec is ZO) then (kp is PM)(ki is NM)(kd is NM)(1)47. If (e is PB) and (ec is PS) then (kp is PM)(ki is NM)(kd is NS)(1)48. If (e is PB) and (ec is PM) then (kp is PB)(ki is NB)(kd is NS)(1)49. If (e is PB) and (ec is PB) then (kp is PB)(ki is NB)(kd is NB)(1)把这49条控制逻辑规那么，键入到模糊规那么库中，如图4。图4 模糊规那么库
15、5模糊PID控制器仿真利用MATLAB软件中的Simulink仿真环境，可以对模糊PID控制器系统进展模拟仿真实验，来检验设计是否到达要求。针对本次控制器设计，我们设置被控对象为，根据被控对象，设置相应的PID参数为：=6;=3;=2。图5为控制器系统在Simulink中的仿真模型。为了方便与传统PID控制器进展比较，在Simulink仿真环境中作出传统PID控制以便于对模糊PID进展比较。在传统PID控制器中设置相应的PID参数为：=6;=3;=2。图6是传统PID与模糊PID控制器在Simulink中的阶跃仿真波形比较。图5传统PID与模糊PID控制器在Simulink中的仿真模型图6传统PID与模糊PID控制器在Simulink中的阶跃仿真波形比较图6中，黄色线为输入的阶跃信号，紫色为输出的传统PID控制信号，青色为输出的模糊PID控制信号，通过图1-7中传统PID控制方式与模糊PID控制控制曲线的比照结果可以看出，模糊控制的控制性能要明显好于传统的PID控制效果。我们把输入信号变为正弦信号再一次进展传统PID与模糊PID控制器的比照。把图5的输入阶跃信号改为输入正弦信号即可进展正弦信号的跟踪。图7是传统PID与模糊PID控制器在Simulink中的正弦仿真波形比较。图7 传统PID与模糊PID控制器在Sim
