《物理测试实验室测量设备的校准.doc》由会员分享，可在线阅读，更多相关《物理测试实验室测量设备的校准.doc（7页珍藏版）》请在金锄头文库上搜索。
1、STANDARD OPERATING PROCEDURESSOP ID:MAINT-004Effective Date:January 28, 2005Section:Maintenance Equipment & CalibrationSub-Section:Calibration Of Physical Test Lab Measuring EquipmentPURPOSE:To describe minimum calibration tolerances and calibration frequencies for inspection, measuring, and test eq
2、uipment used as critical or master instruments in Physical Test Laboratories.标准操作程序标识号：维修-004生效期：2005年1月28日部分:设备维修及校准子部分:物理测试实验室测量设备的校准用途:用来说明在物理测试实验室中用作关键或校准用仪器的检查、测量及测试仪器的最小校准公差和校准频率。Calibration Of Physical Test Lab Measuring EquipmentTable of ContentsPAGEI. INTRODUCTION1A. Purpose1B. Scope1C. Def
3、initions1II. MASTER LIST OF INSPECTION, MEASURING, AND TEST EQUIPMENT2页码I. 介绍1A. 用途1B. 范围1C. 定义1II.检查、测量及测试设备的总清单2MAINT-004Calibration Of Physical Test Lab Measuring EquipmentI.INTRODUCTION介绍A.Purpose用途To describe minimum calibration tolerances and calibration frequencies for inspection, measuring,
4、and test equipment used as critical or master instruments in Physical Test Laboratories.用来说明在物理测试实验室中用作关键或校准用仪器的检查、测量及测试仪器的最小标准公差和校准频率。B.Scope范围This standard is applicable to all of the Plants Physical Test Laboratories facilities.此标准应用于所有工厂物理测试实验室设备。C.Definitions定义CALIBRATION 校准- The comparison bet
5、ween the master instrument of known accuracy and the instrument to be calibrated to detect, correlate, report, or eliminate by adjustment, any variation in the accuracy of the instrument being compared.-将已知精度的校准用仪器与被校准设备进行比较，经过调节，检测、互相关、报告或消除被测设备与已知精度的校准用仪器精度上的不同值。NON-CRITICAL INSTRUMENTS非关键仪器- Thos
6、e measuring instruments that do not affect the characteristics/quality of the product. 这些测量设备不会影响产品的特性/质量。CRITICAL INSTRUMENTS关键仪器- Those measuring instruments that directly affect the characteristics/quality of the product. 这些测量设备直接影响产品的特性/质量。MASTER INSTRUMENTS校准用仪器- Those instruments that are used
7、 as a standard to calibrate other instruments.这些设备被作为标准用来校准其他的设备。N.I.S.T. - National Institute of Standards and Technology.美国科学和技术研究院II.MASTER LIST OF INSPECTION, MEASURING, AND TEST EQUIPMENT检查、测量及测试设备总清单The table below lists minimum calibration frequencies and tolerances for inspection, measuring,
8、 and test equipment used in plant Physical Test Laboratories. 下面的表列出了用于工厂物理测试实验室的检查、测量及测试设备的最低校准频率 和规定公差。 Calibration of the instruments should be done in accordance with Corporate Calibration Policy set forth in Standard Practice MAINT-001. 对于设备的校准，应按照之前给出的标准作法维修-001中设定的全体校准规范进行操作。The frequencies a
9、nd tolerances listed are minimum requirements. Tolerances can be tightened and frequencies shortened if required by the plant.所列出的频率和公差是所需的最低值。可按照工厂的要求减小公差并缩短频率。MASTER LIST OF MEASURING EQUIPMENT测量设备的主清单ACCURACY精度CALIBRATION FREQUENCY校准频率Dynamic Analyzer (RDA) 动态分析器 (RDA) 5%Annual一年一次Solids Analyzer
10、 (RSA) 固态分析器 (RSA) 5%Annual一年一次Instron (1130) Wire Adhesion, Cord Adhesion拉伸强度试验机 (1130)钢丝附着， 帘线附着 1%Annual一年一次Instron (1122) Cord Testing拉伸强度试验机(1122) 帘线测试 1%Annual一年一次Instron (4501) CRA Testing拉伸强度试验机(4501) CRA 测试 1%Annua一年一次lInstron (4201) Ring Tear拉伸强度试验机(4201) 环状撕裂 1%Annual一年一次Instron (4400R) R
11、ing Modulus拉伸强度试验机(4400R) 环状系数 1%Annual一年一次Instron (4465) Dumbbell Tensile拉伸强度试验机(4465)哑铃拉伸 1%Annual一年一次Wallace Plasticity华莱士塑型 2FQuarterlyAging Ovens老化炉 1FQuarterlyOzone Chamber臭氧箱 3%Annual一年一次Flexometer曲率计0.400 Throw0.400 偏心距离Annual一年一次DeMattia曲折试验机300 10 CPM300 10每分钟循环数Annual一年一次Picma Tack皮克玛粘度试验
12、机.01 Kg01 千克Annual一年一次Pico Abrator皮喷砂清理机-Lambound Tester兰朋式磨耗试验机100 mg 20100 毫克 20Annual一年一次Fatigue Failure疲劳破坏-Thickness Gauge (Inches) 厚度计(英寸) .001 Inches .001 英寸Annual一年一次Thickness Gauge (MM) 厚度计(毫米) .01 MM .01 毫米Annual一年一次Timers定时器1 Minute1分钟Annual一年一次Scales天平.1 Gram.1 克Annual一年一次Durometers硬度计 1
13、Semi-Annual半-一年一次Digital Thermometers数字式温度计 0.1%F 0.1%华氏温度Quarterly一季一次Humidity Oven湿度炉Temp. 1C, R.H. 1%温度 1摄氏度， 相对湿度 1%Quarterly一季一次Cure Press (Steam) 加压硫化(蒸汽) 1F 1华氏温度Quarterly一季一次Cure Press (Electric) 加压硫化 (电) 2F2华氏温度Quarterly一季一次Processability Tester加工性能测试仪 3%Semi-Annual半-一年一次Mooney (M1500) 穆尼 (M1500) 1.0 M.U. 1.0 穆尼Semi-Annual半-一年一次Mooney (MV2000E) 穆尼 (MV2000E) 1.0 M.U. 1.0 穆尼Semi-Annual半-一年一次Rheometer (R100) 流速计 (R100)0.13 In.-Lb. 0.13 英寸-磅Semi-Annual半-一年一次Rheometer (MDR 2000) 流速计 (MDR 2000)0.01 In.-Lb. 0.01 英寸-磅Semi-Annual半-一年一次Weights砝码 2%Annual一年一次Page 5 of 5
