《锂电池规格书》由会员分享，可在线阅读，更多相关《锂电池规格书（10页珍藏版）》请在金锄头文库上搜索。
1、 充电器规格书Specification of Battery Charger型号: ES2406S29.2V/6A 锂电池充电器（全铝外壳）29.2V / 6A Li Iron/Li Polymer BATTERY CHARGER 1. 概述General此型号2406S 1559050mm的铝质外壳充电器能在输出29.2Vdc/6A的情况下工作，具有反接保护功能。Battery Charger 2406S 1559050mm can work normally under 29.2Vdc/6A and with reverse polarity protection. 2. 主要参数请预览
2、后下载！Main product specification 最大输出功率Max.output power输入电压Input voltage最高输出电压Output voltage误差范围Combined regulation输出电流Output current误差范围Combinedregulation180W220Vac29.2V+/-0.2Vdc+/-0.2V6A+/-0.2A3. 环境条件Environmental condition序号No.项目Item技术参数Technical specification备注Remark1湿度 Humidity 595% 带包装 With pack
3、age2海拔Altitude3000m正常工作 Work normally4. 技术特征Electrical characteristics4.1 输入特征： Input characteristic序号No.项目Item 技术参数 Technical specification备注 Remark1额定输入电压Rated input voltage220Vac220Vac2电压输入范围Input voltage range180-240Vac3频率AC input voltage frequency5060 Hz4.2 输出特征和充电模式： Output characteristic or c
4、harge stages序号No.项目Item技术参数Technical specification备注Remark1恒流 CC(constant current)29.2Vdc, 6A2恒压CV(constant voltage)29.2Vdc, 6A3浮充 Float stage无20%CC4效率Power efficiency90%输入电压=220Vac, 额定负载Vin=110/220Vac,rated load请预览后下载！4.3 保护特征： Protection characteristics序号No.项目Item技术参数Technical specification备注Remar
5、k1过压保护Over voltage protection是Yes2限压保护Software over voltage protection充电器设置的最大输出电压不会超过电池的最大充电电压。The charger software limits the maximum output voltage to a level suitable for the connected battery system.3过热保护Thermal protection否 No4限流保护Current limiting protection是 Yes恒流At CC mode5短路保护Short circuit p
6、rotection当输出短路时充电器不能正常工作，输出恢复正常，充电器可自行恢复。Short circuit protection should be automatically recovery after remove the condition.6反接保护Reverse polarity protection当输出线接反后充电器不会工作，直到使用者接正确后方可启动。When output wires are reversely connected to the battery the charger will not operate and will work normally when
7、 DC wires are correctly connected.4.4 充电指示 Charging indicator序号No.项目 Item状态 Status备注Remark1电源Power onLED1: 红灯 Red2充电ChargingLED2: 红灯 Red3充满 Fully chargedLED2: 绿灯 Green4输出电压显示Charging Voltage Display否 No5输出电流显示Charging Current Display否 No5. 安全性Safety & EMC序号项目标准 ( 或测试条件)备注请预览后下载！No.ItemStandard (or t
8、est condition)Remark1耐压测试Electric strength test输入-输出Input-output1500Vac/10mA/1min无故障No breakdown2绝缘电阻Isolation resistance输入-接地Input-ground10Mohm500Vdc输出-接地Output-ground10Mohm500Vdc3泄漏电流 Leakage current3.5mAVin=264Vac4低电压测试LVDEN60335-1:2002+EN60335-2-29:2002备注：辨识A：在技术要求范围内，充电器功能正常；Remark: Discriminat
9、ion A- Function OK under technical requirement range; 辨识R：只有由外部干扰信号引起的保护装置（保险丝）损坏，整个设备在更换保护装置和重设运行参数后才能正常工作，因机械性损坏和设备故障的设备却不能。Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interference signal of outside is allowed, and the
10、 whole equipment can work normally after replacement of protection device and reset of running parameter6. 环境测试要求Environmental testing requirements序号No.项目Item技术参数Technical specification备注Remark1最高工作温度High temperature ambient operating+40性能正常 Features OK2最低工作温度Low temperature ambient operating-10性能正常
11、Features OK3最高存储温度High temperature storage+70在恢复正常温度2小时后，充电器能正常工作。Work normally after recovery under normal temperature for 2 hours4最低存储温度Low temperature storage-40在恢复正常温度2小时后，充电器能正常工作。Work normally after recovery under normal temperature for 2 hours5随机振动20Hz to 2000Hz 3Grms 20hours per axis请预览后下载！R
12、andom vibration6重复震动Repetitive shock40g peak 3 orthogonal axes, 3+ and 3- in each axis, 11ms pulse width7热冲击Thermal shock-35 to 75, 3min transition, 2.5hours dwell, 200cycle8跌落测试Drop testBS EN60068-2-32:1993 TEST ED: free fall appendix B7. 机械特征Mechanical characteristic:外壳材质：铝Shell material: Aluminum
13、外壳尺寸: 长*宽*高=1559050毫米Outline dimension: L*W*H=1559050mm输入接口: 通过IEC 标准Input socket: meets IEC standard电源线: 1.5米长AC wires: 1.5m length输出线: 1.0米长DC wire: 1.0m length净重: 0.9千克Net Weight: 0.9Kg8. 包装，运输方式和存储方式 Package, transportation & storage8.1 包装 Package: 包装盒内有产品名称，型号，生产厂家名称，安全标准，序号，使用说明书以及装箱单。 There is product name, model, name of manufacturer, safety approva
