《GeN2调试手册》由会员分享，可在线阅读，更多相关《GeN2调试手册（37页珍藏版）》请在金锄头文库上搜索。
1、GeN2 调试手册 .Field Engineering Department FED目 录1.0. 总鉴.41.1. 技术总览51.2. 系统要求52.0. 检修模式的启动.62.1. 检查接线及主电源.62.2. 送电操作62.3. 启动TCB82.4. 启动SPB.82.5. 确认RSL及效劳器通信92.6. 启动BRE电子释放抱闸装置.102.7. 确认MCB信号及参数.112.7.1合同参数M-3-1.112.7.2.运行曲线参数M-3-2-.132.7.3.其它参数M-3-4、M-3-5-2.132.8. TCB参数设置.142.9. 编码器的调整.142.10. 检查运行及编码器
2、方向.173.0. 检查平安装置183.1. 平安钳及其传动机构的测试.183.2. 测试BRE电子释放抱闸装置.184.0. 平层感应系统185.0. 第一次正常运行205.1. 串行通信链路205.2. 检查井道信号206.0. 启动门系统DCSS4 、5.217.0. 自学习运行.217.1. 自学习运行.217.2. 厅门检测程序.238.0. 启动LWB称重装置.248.1. 参数确认.258.2. 偏移量校准.258.3. 增益量校准.258.4. 负载的监测.269.0. 平层精度调整269.1. 参数说明.269.2. 平层精度.2710.0. 参数储存2811.0. TCB的
3、进一步功能启动2811.1. 楼层位置指示器2911.2. 检查ADO与RLV功能.2911.3. 远程监控系统2912.0. SPB的使用.2912.1. 介绍.2912.2. 缩写说明3012.3. 接口说明3212.4. 状态灯LED说明.3312.5. 电池充电显示.3612.6. 按钮3612.7. 扩展功能.3712.8. 其它部件说明.3812.8.1. REM效劳按钮.3812.8.2. 门区显示器.3812.8.3. 合同速度显示器.3912.8.4. 轿厢位置显示器.3912.8.5. 轿厢速度各方向显示4012.8.6. 蜂鸣器4112.8.7. 通信检查.4213.0.
4、 OVFww(MCB)的效劳器使用.4313.1. 效劳器菜单流程图4313.2. 效劳器显示，监测M-14413.3. 测试.4513.4. 缩写解释.4813.4.1. 运行命令状态及说明.4813.4.2. 运行逻辑状态及说明.4913.4.3. 重要变量说明5014.0. OVFww驱动故障信息5014.1. 故障记录格式及说明(M-2-2) .5014.2.1 系统与运行控制信息.5114.2.2 驱动器警告信息.5114.2.3 称重系统相关信息.5114.2.4 运行指令信息5114.2.5 运行逻辑状态相关信息.5114.2.6 驱动控制相关信息.5114.2.7 自学习运行及
5、PCT调整相关信息.51 14.3. MCB参数表5910.总览The Gen 2 System is an machine room less system of the elevator control.There are two controller cabinets;GeN2 is a machine-room-less lift with unsurpassed levels of fort, reliability and safety. GeN2 offers passengers a quieter, smoother and more elegant ride than an
6、y lift system in its class. Its design enables architects to design buildings without a machine room. Builders will benefit from quicker installation and minimal interference with other trades. And owners can operate the building more economically and with more rentable space. GeN2是由一个无机房电梯系统控制的,包括以
7、下两主要控制局部：GeN2是一种舒适的，高可靠性和平安性的无机房电梯。GeN2电梯提供给乘客更宁静的，平滑的和一流的运行。它使建筑师无须考虑电梯的机房。所以建筑商可得益于在其贸易方面更快的安装及更小的干扰。及业主能有更多可出租的空间，有更高的经济效益。 the controller mounted in the hoistway contents the Operational control and Drive control. The Operational control is realized by the Traction Control Board (TCB) and the Dr
8、ive Control by the Motion Control Board (MCB) / Vector Control Board (VCB).主控制柜安装在井道，包括操作控制和拖动控制。操作控制通过牵引控制电子板TCB实现，拖动控制通过动行控制电子板MCB和矢量制电子板VCB实现。 the E&I panel mounted in the hoistway door panel at top landing contents the Service Panel Board (SPB), the Brake Release Board (BRE), the ERO Control and
9、 the Emergency Power Unit.E&I控制屏安装在顶层厅门旁，包括检修电子板SPB，抱闸释放电子板BRE，ERO检修开关。A further Board, the Load Weighing Board (LWB) is mounted in the COP.And for the Door control the Door Control Subsystem DCSS5 is used.还有其它电子板，如电子称重板LWB安装于COP，门机控制板等。1.1.技术总览The following Chart gives you an overview about the use
10、d Control Subsystems of the whole Gen 2 System.以下图表给出一个关于整个GEN2的各个控制子系统的定位总览。1.2.系统要求Starting up of the WWOVF Drive - System only should be performed by authorisizied personal!WWOVF 驱动系统启动只应由经授权的人员执行!The mechanical works of hoistway and cabine as well as the electrical installation in the hoistway,
11、controller and E&I Panel have to be finished to ensure inspection run. 必须完成井道和机房的机械工作以及在井道、控制柜和E&I板的电气安装以确保检修运行.The encoder have to be mounted at machine and properly connected with MCB.一定要将编码器安装在主机上并正确地与MCB连接The electrical connections have to be installed pletely and checked.必须完整地安装电气连接并检查.2.0. 以检修模式运行The mechanical works of hoistway, cabine, controller, machine and electrical installation have to be finished
