《网点路由器切换实施详细步骤》由会员分享,可在线阅读,更多相关《网点路由器切换实施详细步骤(22页珍藏版)》请在金锄头文库上搜索。
1、网点路由器上线操作步骤准备工作切换网点信息收集网点名称:武侯永丰红牌楼分理处网点地址:红牌楼二街61-63号网点Fastethernet 0接口IP:10.36.251.46 子网掩码:255.255.255.252网点Fastethernet 1接口IP:30.1.36.202 子网掩码:255.255.255.0网点对应的中心端7609路由器接口:G1/0/1.342网点对应的中心端7609路由器接口IP:10.36.251.45网点对应的二类网IP:30.1.36.8VPN备份IP地址:10.2.239.4到达网点后询问网点农商行员工该网点机构号,告知中心端实施人员后方可开始实施。所有网
2、点切换前提前准备网点相关资料网点部分第一步. 一类网线路连通性测试笔记本配置网点Fastethernet0接口IP,ping网点对应的中心端路由器接口IP打开命令提示符,执行ping 10.36.251.45 t如果ping不通,立刻联系中心实施人员。第二步. 二类网线路连通性测试笔记本配置网点Fastethernet1接口IP,ping网点对应的二类网IP打开命令提示符,执行ping 30.1.36.8 t,如下图:如果ping不通,立刻联系中心实施人员。第三步. 保存网点设备配置(此步骤非常重要)通过Consloe线缆登录网点路由执行配置保存操作。(登录路由器后,直接输入wr,然后输入ye
3、s,回车)CD_NJ_65_hpl_2816#wrAre you sure to overwrite /flash/startup (Yes|No)?yesBuilding Configuration.doneWrite to startup file . OKCD_NJ_65_hpl_2816#CRT上记录会话,保存、备份现有配置CD_NJ_65_hpl_2816#show run通过Consloe线缆登录网点华为交换机执行配置保存操作。(登录交换机后输入save)该步骤完成后,在向网点人员确认可以中断网络后,给中心端实施人员打电话通知中心端做配置更改。该步骤非常重要!第四步. 网点线路切换
4、上图为迈普2816路由器接口图:接口描述:左起第一个接口:con/aux,此接口为Consloe接口,用于配置路由器使用。左起第二个接口:fastethernet0,此接口用于连接电信的MSTP RJ45网线。左起第三个接口:fastethernet1,此接口用于连接网点的华为交换机。左边24个接口:网点局域网交换机机。实施过程中线缆连接分为三步:1. 将fastethernet0与电信MSTP设备连接2. 将fastethernet1与华为交换机设备连接3. 对电信设备、华为交换机到迈普2816路由器的线路进行打标(考虑标签机)VPN备份链路华为xx端口华为xx端口VPN备份链路第五步. 网
5、点线路质量测试(同时查看接口是否为双工)通过Consloe登录网点路由器,更改Fastethernet0接口和Fastethernet1接口IP地址 ,执行链路检测操作1. 修改接口IP地址脚本文件:2. 测试MSTP线路质量CD_NJ_65_hpl_2816#pingProtocol ip: Target IP address or hostname: 10.36.251.45Repeat count 5: 1000Datagram size 76: 1500Timeout in seconds 2: Extended commands no: yesSource address or in
6、terface: f0Type of service 0: Set DF bit in IP header? no: Validate reply data? no: Data pattern abcd: Loose, Strict, Record, Timestamp, Verbosenone: Sweep range of sizes no: Press key (ctrl + shift + 6) interrupt it.Sending 1000, 1500-byte ICMP Echos to 10.36.251.45 , timeout is 2 seconds:!Success
7、rate is 100% (1000/1000). Round-trip min/avg/max = 16/17/66 ms.CD_NJ_65_hpl_2816#CD_NJ_65_hpl_2816#ping Protocol ip: Target IP address or hostname: 30.1.36.8Repeat count 5: 1000Datagram size 76: 1500Timeout in seconds 2: Extended commands no: yesSource address or interface: f1Type of service 0: Set
8、DF bit in IP header? no: Validate reply data? no: Data pattern abcd: Loose, Strict, Record, Timestamp, Verbosenone: Sweep range of sizes no: Press key (ctrl + shift + 6) interrupt it.Sending 1000, 1500-byte ICMP Echos to 30.1.36.8 , timeout is 2 seconds:!.!Success rate is 99% (999/1000). Round-trip min/avg/max = 0/0/16 ms.CD_NJ_65_hpl_2816#3. 查看接口双工查看Fastethernet0接口状态:show interface Fastethernet0CD_NJ_65_hpl_2816#sh int f0fastethernet0: line protocol is up Flags: (0xc) BROADCAST MULTICAST ARP RUNNING Type: ETHERNET_CSMACD Description: For_MSTP()