《汽车起重机起重性能表》由会员分享，可在线阅读，更多相关《汽车起重机起重性能表（32页珍藏版）》请在金锄头文库上搜索。
1、20 500t 汽车吊额定性能表叮叮小文库20 吨汽车吊机额定性能表主臂长度（ m）主臂 +寸臂回转半径（ m10.212.5814.9717.3519.7322.1224.524.5+7.53.0203.517.215.94.014.614.612.64.512.7512.711.710.55.011.611.311.39.75.510.4510109.18.16.09.3998.57.66.97.07.247.37.417.26.76.15.58.05.996.16.176.225.95.459.05.135.215.255.34.84.510.04.354.434.484.524.442
2、.112.03.263.323.363.393.411.714.02.492.532.562.581.416.01.91.941.961.218.01.451.47120.01.080.8822.00.760.7524.00.6327.00.51叮叮小文库25 吨汽车起重机起重性能表（主臂）工作半径 （m）吊臂长度 （ m）10.213.7517.320.8524.427.9531.532517.53.520.617.512.29.541817.512.29.54.516.315.312.29.57.5514.514.412.29.57.55.513.513.212.29.57.57612.3
3、12.211.39.27.575.16.511.21110.58.87.575.1710.2109.88.57.275.17.59.49.29.18.16.86.75.188.68.47.86.66.45.18.57.86.37.2597.276.8 I66.14.81065.85.6|1244.14.14.23.93.7142.933.12.93162.22.32.22.3181.61.81.71.7201.31.31.32210.91240.70.8260.50.5280.4290.330（注：本表内黑格及黑格以上栏目的数字为吊臂强度所决定，其下面栏目数字为倾翻力矩决定）25 吨汽车起重机
4、起重性能表（副臂）主臂主角7.5 副臂副臂倾角5 度副臂倾角30 度80 度2.51.2575 度2.51.2570 度2.051.1565 度1.751.160 度1.551.0555 度1.31.050 度1.050.82叮叮小文库30 吨汽车起重机性能表（一）主要技术参M数工作半径名称参数（ m）全车总重32.2t3.00最大爬坡能力31%3.35最大提升高度34.00m13.50吊臂全伸时长度31.00m4.00吊臂全缩时长度10.00m14.50最小转弯半径11.50m4.8最大仰角805.030t 吊钩重0.35t5.512t 吊钩重0.20t6.04t 吊钩重0.10t6.510
5、m 吊臂时钢丝绳7.0数8 根10-17m 时钢丝绳5 根7.5数24m 时钢丝绳数4 根8.031m 时钢丝绳数3 根8.59.810.011.012.014.016.018.020.022.024.026.027.0主臂起重性能支腿全伸不用支腿10.00m17.00m24.00m31.00m10.00m30.0020.008.0030.00I 20.007.0028.1020.006.4024.20I 20.005.1021.4020.0013.004.2020.00 1I 20.00I13.003.7019.2019.20I13.003.4017.5017.5013.002.8016.0
6、016.0013.002.3014.6014.6013.009.001.9013.5013.5012.009.001.6012.0012.0011.209.001.3010.5010.5010.509.001.009.409.409.007.207.207.706.956.957.505.805.806.404.904.905.553.453.454.202.503.201.802.451.301.900.851.501.100.750.653叮叮小文库30 吨汽车起重机性能表（二）吊臂角度工作半径使用 8.45m 副臂倾吊臂角度工作半径使用 13.5m 副臂倾角 5角 5807.94.008
7、09.32.5078.5 9.54.007712.02.507810.23.807612.72.357611.23.307414.12.107412.22.907215.61.957213.42.707017.11.807014.62.506818.51.656816.02.356619.91.506617.32.206421.31.406418.52.106222.71.306219.82.056024.01.206020.71.855825.31.155821.91.655527.11.055523.61.305427.70.955424.11.155228.80.805225.00.95
8、5029.90.655025.80.754830.90.554826.80.60注： 1、若副臂在工作位置，但仍用主臂吊装，主臂的起重性能应相应的减去1.4t2、使用副臂吊装时，主臂的角度不得大于45, 否则将倾翻4叮叮小文库50 吨汽车起重机性能表（主表）不支第五支腿，吊臂位于起重机前方或后方；支起第五支腿，吊臂位于侧方、后方、前方主臂长度 （ m）工作半径 （m ）10.7018.0025.4032.7540.103.050.003.543.004.038.004.534.005.024.705.528.0023.506.024.0022.2016.306.521.0015.007.018.50 18.0014.1010.208.014.5014.0012.409.207.509.011.5011.2011.108.306.5010.0
