《常用PP厚度计算》由会员分享，可在线阅读，更多相关《常用PP厚度计算（3页珍藏版）》请在金锄头文库上搜索。
1、文件名稱4.1.4.2.2常6用 PP膠片規格常用PP膠片規格（廠牌：南亞）PP類型含膠量填膠前厚度PP類型含膠量填膠前厚度PP類型含膠量填膠前厚度1080RC62%2.97mil2116RC50%4.73mil7628RC43%7.73 mil1080MRRC65%3.28mil2116MRRC54%5.15 m订7628MRRC47%8.51 mil1080HRRC68%3.65mil2116HRRC58%5.77 mil7628HRRC50%9.18 m订4.1.4.2.2常用壓合疊構（1四層板成品板厚0.8mm1.0mm1.2mm1.6mm外層銅厚H OZH OZH OZH OZPP膠
2、片2116MR7628HR7628MR2116HRCore板厚度0.38mm 1/1OZ0.38mm 1/1OZ0.60mm 1/1OZ1.20mm 1/1OZPP膠片2116MR7628HR7628MR2116HR外層銅厚H OZH OZH OZH OZ東莞聯橋電子有限公司(2)六層板成品板厚0.8mm1.0mm1.2mm1.6mm外層銅厚H OZH OZH OZH OZPP膠片2116MR2116HR1080MR2116MRCore板厚度0.11mm 1/10Z0.18mm 1/1OZ0.38mm 1/1OZ0.50mm 1/1OZPP膠片2116MR2116HR1080MR2116MRC
3、ore板厚度0.11mm 1/1OZ0.18mm 1/1OZ0.38mm 1/1OZ0.50mm 1/1OZPP膠片2116MR2116HR1080MR2116MR外層銅厚H OZH OZH OZH OZ(3八層板成品板厚1.0mm1.2mm1.6mm2.0mm外層銅厚H OZH OZH OZH OZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm 1/1OZ0.13mm 1/1OZ0.26mm 1/1OZ0.38mm 1/1OZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm 1/1OZ0.13mm 1/1OZ0.26mm
4、1/1OZ0.38mm 1/1OZPP膠片1080HR2116HR2116HR2116HRCore板厚度0.13mm 1/1OZ0.13mm 1/1OZ0.26mm 1/1OZ0.38mm 1/1OZPP膠片1080HR2116HR2116HR2116HR外層銅厚H OZH OZH OZH OZ(4十層板成品板厚1.2mm1.6mm2.0mm2.2mm外層銅厚H OZH OZH OZH OZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm 1/1OZ0.21mm 1/1 OZ0.26mm 1/1OZ0.30mm 1/1OZPP膠片1080HR1080HR211
5、6MR2116MRCore板厚度0.11mm 1/1OZ0.21mm 1/1 OZ0.26mm 1/1OZ0.30mm 1/1OZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm 1/1OZ0.21mm 1/1 OZ0.26mm 1/1OZ0.30mm 1/1OZPP膠片1080HR1080HR2116MR2116MRCore板厚度0.11mm 1/1OZ0.21mm 1/1 OZ0.26mm 1/1OZ0.30mm 1/1OZPP膠片1080HR1080HR2116MR2116MR外層銅厚H OZH OZH OZH OZ以上均為理論疊構，具體需依銅箔厚度&內
6、層殘銅率選擇不同的PP&Core板制作 4.1.4.2.2壓8合疊構設計(1) 、优先选用厚度较大的芯板(尺寸稳定性相对较好)(2) 、优先选用成本低之pp (对于同种玻璃布型prepreg树脂含量高低基本不影响价格)(3) 、优先选用结构对称(4) 、介质层厚度内层铜箔厚度x2(5) 、1-2层或兩芯板间禁止单张使用低树脂含量prepreg(6) 、对于有5张或以上的半固化片排在一起或介电层厚度大于25mil中间prepregi光板代替(7) 、內層銅厚為2oz底铜且1-2層或兩芯板間绝缘层厚度14mil时，禁止使用单张prepre,最外层需用高树脂含量prepreg(8) 、内层铜厚1oz的板，1-2層或兩芯板間使用1张prepreg寸,该prepreg需选用高树脂含量(9) 、内层铜厚oz的板禁止用单张PP,般不用7628,须使用多张树脂含量高的prepre,如106、1080、2116-(10) 、对于含有无铜区大于33 或1対的多层板，芯板间一般不单张使用prepreg
