《505编程方式工作卡》由会员分享，可在线阅读，更多相关《505编程方式工作卡（8页珍藏版）》请在金锄头文库上搜索。
1、附 录 A505 PROGRAM MODE WORKSHEET505编程方式工作卡GOVERNOR SERIAL NUMBER_（调速器顺序号）_ APPLICATION_使用场合_ DATE_日期_For details on individual settings, refer to Chapter 5.有关各个设定值的详细内容，请参阅第五章TURBINE START 汽轮机起动Manual Start _YES _ NO _ 手动起动Automatic Start _YES _ NO _ 自动起动Semiautomatic Start _YES _ NO _ 半自动起动Rate to M
2、in (RPM/Sec) _ RPM/SEC 至最小转速速率Valve Lmtr Rate (%/Sec) _ %/SEC 阀位限制器速率Use Idle/Rated? _YES _ NO _ 采用暖机/额定Idle Setpt (RPM) _ RPM 暖机转速设定值Rated Setpt (RPM) _ RPM 额定转速给定值Idle/Rtd Rate (RPM/SEC) _ RPM/SEC 暖机/额定速率Use Auto Start Sequence _YES _ NO _ 采用顺序自动起动Cold Start = ( xx Hrs ) _ HRS 冷态起动Hot Start = ( xx
3、 Hrs) _ HRS 热态起动Low Idle Setpt (RPM) _ RPM 低暖机转速设定值Low Idle Delay (Cold) _ MIN 低暖机转速保持（冷态）Low Idle Delay (Hot) _ MIN 低暖机转速保持（热态）Rate to Hi Idle (Cold) _ RPM/SEC 至高暖机转速速率（冷态）Rate to Hi Idle (Hot) _ RPM/SEC 至高暖机转速速率（热态）High Idle Setpt (RPM) _RPM 高暖机转速设定值High Idle Delay (Cold) _ MIN 高暖机转速保持（冷态）High Idl
4、e Delay (Hot) _ MIN 高暖机转速保持（热态）Rate to Rated (Cold) _ RPM/SEC 至额定转速速率（冷态）Rate to Rated (Hot) _ RPM/SEC 至额定转速速率（热态）Rated Setpt (RPM) _ RPM 额定转速设定值Auto Halt at Idle Setpts _ YES _NO _ 在暖机转速下自动暂停Ext Trips in Trip Relay _ YES _NO _ 外部跳闸释放跳闸继电器Reset Clears Trip Output _ YES _NO _ 复位清除跳闸输出SPEED CONTROL 转速
5、控制Teeth Seen by MPU _ 测速齿轮齿数Gear Ratio 1 :_ 速比 1：Failed Speed Level(RPM) _RPM 失效转速值Use Speed Input #2? _ YES _NO _ 采用 2#转速输入Failed Speed Level(RPM) _RPM 失效转速值Off-Line Prop Gain _ % 脱机比例增益Off-Line Int Gain _ rps 脱机积分增益Off-Line Deriv Ratio _ % 脱机微分率 A-1On-Line Prop Gain _ % 联机比例增益On-Line Int Gain_ rps
6、 联机积分增益On-Line Deriv Ratio _ % 联机微分率SPEED SETPOINT VALUES 转速给定值Overspeed Test Lmt (RPM) _RPM 超速试验极限值Overspeed Trip (RPM) _RPM 超速跳闸转速Max Governor Speed (RPM) _RPM 调速器上限转速Min Governor Speed (RPM) _ RPM 调速器下限转速Setpt Slow Rate(RPM/SEC) _ RPM/SEC 给定值慢速率Use Remote Speed Setpt ?_YES _NO _ 采用远程转速控制给定值Rmt Sp
7、d Setpt Max Rate _ RPM/SEC 远程转速控制给定值最大速率Use Critical Speeds? _ YES _ NO _ 使用临界转速Critical Speed Rate _ RPM/SEC 临界转速速率Critical Speed 1 Max _ RPM 第一临界转速上限值Critical Speed 1 Min _ RPM 第一临界转速下限值Use Critical Band 2 ? _YES _NO _ 使用临界转速范围2Critical Speed 2 Max _ RPM 第二临界转速上限值Critical Speed 2 Min _ RPM 第二临界转速下
8、限值OPERATING PARAMETERS 操作参数Generator Application? _YES _NO _ 用于发电机机组Use Gen Brkr Open Trip ?_YES _NO _ 采用发电机断路器断开跳闸Use Tie Brkr Open Trip ? _ YES _NO _ 采用电网断路器断开跳闸Use KW Droop? _YES _NO _ 使用KW不等率KW Max Load _ _KW KW最大负荷Droop (%) _% 不等率Rated Spd Setpt _ RPM 额定转速给定值Use Freq Arm/Disarm ?_ YES _ NO _ 采用
9、频率介入/退出Use Local/Remote _ YES _ NO _ 采用就地/远程DRIVER CONFIGURATION 驱动器组态Act #1 is 4-20mA? _YES _NO _ 1#执行机构为4-20mAInvert Driver Outputs ? _YES _NO _ 驱动器输出反向Use Act 1 Flt Shutdown _YES _NO _ 使用1#执行机构故障停机Act #1 Dither _% 采用执行机构颤动Use Actuator #2? _ YES _NO _ 采用2#执行机构Act #2 is 4-20mA? _YES _NO _ 2#执行机构为4-
10、20mAAct #2 Offset (%) _% 2#执行机构偏置值Use Act 2 Flt Shutdown _YES _NO _使用2#执行机构故障停机Act #2 Dither (%) _% 采用2#执行机构颤动Use Act #2 as Readout? _YES _NO _ 2#执行机构读数输出Act #2 Readout is: _% 2 #执行机构读数输出为Readout 4mA Value _ Units 读数输出4mA值Readout 20mA Value _ Units读数输出20mA值ANALOG INPUTS 模拟输入A-2Analog Input # 1 Function _ 1#模拟输入功能Input 1 4mA Value _ Units 1#输入4mA值Input 1 20mA Value_ Units 1#输入20 mA值Analog Input # 2 Function _ 2#模拟输入功能Input 2 4mA Value _ Units 2#输入4mA值Input 2 20mA Value _ Units 2#输入20 mA值Analog Input # 3 Function _ 3#模拟输入功能Input 3 4mA V
