《Aruba2400移动控制器基本操作-v2》由会员分享，可在线阅读，更多相关《Aruba2400移动控制器基本操作-v2（3页珍藏版）》请在金锄头文库上搜索。
1、Aruba 交换机根本操作命令登录：(Aruba2400)User: adminPassword: * 缺省口令通常是adminNOTICENOTICE - This switch has active licenses that will expire in 26 daysNOTICENOTICE - See show license for details.NOTICE(Aruba2400) enPassword:* 缺省口令通常是admin(Aruba2400) #恢复出厂值：(Aruba2400) #write eraseAll the configuration will be de
2、leted. Press y to proceed :Write Erase successful(Aruba2400) #reloadDo you really want to reset the system(y/n): yAruba交换机重启初始化配置：Enter System name Aruba2400: Enter VLAN 1 interface IP address 172.16.0.254: Enter VLAN 1 interface subnet mask 255.255.255.0: Enter IP Default gateway none: Enter Switch
3、 Role, (master|local) master: Enter Country code (ISO-3166), for supported list: CNYou have chosen Country code CN for China (yes|no)?: yEnter Password for admin login (up to 32 chars): *Re-type Password for admin login: *Enter Password for enable mode (up to 15 chars): *Re-type Password for enable
4、mode: *Do you wish to shutdown all the ports (yes|no)? no: Current choices are:System name: Aruba2400IP Default gateway: noneSwitch Role: masterCountry code: CNPorts shutdown: noIf you accept the changes the switch will restart!Type to go back and change answer for any questionDo you wish to accept
5、the changes (yes|no)yCreating configuration. Done.保存配置文件：(Aruba2400) enPassword:*(Aruba2400) #configure t(Aruba2400) # copy running-config tftp: 192.168.4.100 aruba2400-0904.cfg恢复配置文件：(Aruba2400) enPassword:*(Aruba2400) #configure t(Aruba2400) (config) #copy tftp: 172.16.0.100 aruba2400-0904.cfg fla
6、sh: 2400.bak(Aruba2400) (config) #copy flash: 2400.bak flash: 2400.cfg(Aruba2400) (config) #boot config-file 2400.cfg(Aruba2400) (config) #reloadDo you really want to reset the system(y/n): ySystem will now restart!Image 升级：(Aruba200) #show bootConfig File: default.cfgBoot Partition: PARTITION 0(Aru
7、ba2400) #show image version(Aruba2400) #copy tftp: 172.16.1.50 A2400_FCS2.0.X_6577 system: partition 1Upgrading partition 1(Aruba2400) #reload(Aruba200) #boot system partition 0PC：telnet 172.16.0.254 2300connect 1/2重启AP4秒内Stoppurgenvbootlogin as: adminadmin10.3.22.20s password:(Aruba-master) enableP
8、assword:*(Aruba-master) #configure terminalEnter Configuration commands, one per line. End with CNTL/Z(Aruba-master) (config) #telnet soeOnce SOE is enabled, you can connect to the AP serial port with the following procedure:1 Telnet to the Aruba mobility controller using port 23002 Log in using the admin account3 Connect to the Ethernet port that the AP is attached toUser: adminPassword: *Available commands: connect exit (no args)soe connect 2/0Connecting to 2/0 at 9600 baud 8N1Type . to disconnect
