《AD736外文翻译》由会员分享，可在线阅读，更多相关《AD736外文翻译（14页珍藏版）》请在金锄头文库上搜索。
1、FEATURES Computes True rms value Average rectified value Absolute value Provides 200 mV full-scale input range (larger inputs with input attenuator) High input impedance: 1012 Low input bias current: 25 pA maximum High accuracy: 0.3 mV 0.3% of reading RMS conversion with signal crest factors up to 5
2、 Wide power supply range: +2.8 V, 3.2 V to 16.5V Low power: 200 mA maximum supply current Buffered voltage output No external trims needed for specified accuracy AD737an unbuffered voltage output version with chip power-down also availableGENERAL DESCRIPTION The AD736 is a low power, precision, mono
3、lithic true rms-to-dc converter. It is laser trimmed to provide a maximum error of 0.3 mV 0.3% of reading with sine wave inputs. Furthermore, it maintains high accuracy while measuring a wide range of input waveforms, including variable duty-cycle pulses and triac (phase)-controlled sine waves. The
4、low cost and small size of this converter make it suitable for upgrading the performance of non-rms precision rectifiers in many applications. Compared to these circuits, the AD736 offers higher accuracy at an equal or lower cost. The AD736 can compute the rms value of both ac and dc input voltages.
5、 It can also be operated as an ac-coupled device by adding one external capacitor. In this mode, the AD736 can resolve input signal levels of 100 V rms or less, despite variations in temperature or supply voltage. High accuracy is also maintained for input waveforms with crest factors of 1 to 3. In
6、addition, crest factors as high as 5 can be measured (introducing only 2.5% additional error) at the 200 mV full-scale input level. The AD736 has its own output buffer amplifier, thereby pro-viding a great deal of design flexibility. Requiring only 200 A of power supply current, the AD736 is optimiz
7、ed for use in portable multimeters and other battery-powered applications. The AD736 allows the choice of two signal input terminals: a high impedance FET input (1012 ) that directly interfaces with High-Z input attenuators and a low impedance input (8 k) that allows the measurement of 300 mV input
8、levels while operating from the minimum power supply voltage of +2.8 V, 3.2 V. The two inputs can be used either single ended or differentially. The AD736 has a 1% reading error bandwidth that exceeds 10 kHz for the input amplitudes from 20 mV rms to 200 mV rms while consuming only 1 mW. The AD736 i
9、s available in four performance grades. The AD736J and AD736K grades are rated over the 0C to +70C and 20C to +85C commercial temperature ranges. The AD736A and AD736B grades are rated over the 40C to +85C industrial temperature range. The AD736 is available in three low cost, 8-lead packages: PDIP,
10、 SOIC, and CERDIP. PRODUCT HIGHLIGHTS 1. The AD736 is capable of computing the average rectified value, absolute value, or true rms value of various input signals. 2. Only one external component, an averaging capacitor, is required for the AD736 to perform true rms measurement. 3. The low power cons
11、umption of 1 mW makes the AD736 suitable for many battery-powered applications. 4. A high input impedance of 1012 eliminates the need for an external buffer when interfacing with input attenuators. 5. A low impedance input is available for those applications that require an input signal up to 300 mV
12、 rms operating from low power supply voltages. SPECIFICATIONS At 25C 5 V supplies, ac-coupled with 1 kHz sine wave input applied, unless otherwise noted. Specifications in bold are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing qualit
13、y levels.Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Expos
14、ure to absolute maximum rating conditions for extended periods may affect device reliability.THEORY OF OPERATIONAs shown by Figure 18, the AD736 has five functional subsections: the input amplifier, full-wave rectifier (FWR), rms core, output amplifier, and bias section. The FET input amplifier allo
15、ws both a high impedance, buffered input (Pin 2) and a low impedance, wide dynamic range input (Pin 1). The high impedance input, with its low input bias current, is well suited for use with high impedance input attenuators. The output of the input amplifier drives a full-wave precision rectifier th
16、at, in turn, drives the rms core. The essential rms operations of squaring, averaging, and square rooting are performed in the core using an external averaging capacitor, CAV. Without CAV, the rectified input signal travels through the core unprocessed, as is done with the average responding connection (see Figure 19). A final subsection, an output amplifier, bu
