《技术协议和合同注意问题》由会员分享，可在线阅读，更多相关《技术协议和合同注意问题（8页珍藏版）》请在金锄头文库上搜索。
1、技术协议和合同注意问题1工厂具体使用条件要写清楚：（相应条件写清楚，可根据具体情况进行更改）例如：Requirements for the Factory1.1电流种类及电压Current and Voltage供电方式采用TN-S （三相五线制）方式 Power supply should be TN-S （three phases five lines） 电压：380V15% Voltage: 380V15%频率 50Hz1% Frequency: 50Hz1%1.2压缩空气：Compressed Air:压力 0.5-0.6Mpa， Pressure: 0.5-0.6Mpa进入设备温度：
2、q室温 Temperature: indoor temperature压力露点温度：N5C Dew Point Temperature: 5 C1.3厂房温度和湿度Temperature and Humidity of the Factory 温度：夏季0C Temperature: in summer0C湿度65% Humidity65%1.4工厂屋架Framework of the Ceiling厂房屋架下弦高度：7.5m Lower boom height of the roof truss: 7.5m 设备安装地坪：整体地坪，地坪承载6t/m2 （400MM混凝土加双层钢筋，设备不需作
3、单独 的基础） Terrace for installing the equipment: overall terra, bear weight 6t/m2 （400MM concrete with double deck of reinforcing steel bar, equipment do not need to be sole base）2.工件验收问题：A 一般德国钥匙都是全部检查，并找出几个关键项目交PPK(CMK)N1.67或1.33.；B培训等服务随机服务不要写免费，这样反而不利，应该写包含在机床总价内。C.根据以往的经验随机资料还应该有光盘一份，必须有其他相关备件等资料以
4、便购买和维修。详细见第三条。这是一个大厂提出的一般性资料要求。D机床夹具没有提是否包含应该写上。3提供给最终用户的技术资料(可根据具体情况进行调整或更改)Technical Documents Provided by Suppliers to the Final Users供方应向需方提供机床安装、操作、使用、维修必需的全套资料。Suppliers should provide complete documents about installation, operation, use and maintenance of the machine tool to the Demanders.A.
5、1 一般性要求General RequirementsA.1.1机床操作手册、编程手册采用中文和英文(英文手册一套，中文手册两套)，机床精度 检验卡和备件清单采用中英文对照，其它技术资料采用中文或英文，格式应满足需方 相关要求。文件数量：纸质三套，电子文档一份(CD盘)。Machine manual pamphlet and programming manual should be both in Chinese and in English (one set of English and two sets of Chinese), accuracy checking card and spa
6、re parts list should be inChinese and English; other documents should be in Chinese or in English and the formats shouldPeiimeet requirements of the Demanders. Documents: threeessartck a Difelecipsal one(CD )文件规格应保证其内容清晰、易懂。这些资料上应带有以下说明：机床或设施的名称，带修改标记的修改日期及内容。Documents should be clear and easy to un
7、derstand. They should have following content: name of the machine tool or of the equipment; amended date and content with signs.A.2设备资料清单(图形文件用Autocad2004以上版本格式，其余文件用Word或Excel)List of Equipment Documents (drawing should be above Autocad2004 version, others can be Wordor Excel)序号SN文件名称Documents Name
8、1机床总图General drawing of the machine tool2机床的平面布置图(含三维尺寸、轴线位置、进排管联结、分支点位置及大小)Plane layout of the machine tool (include tricone size, axes position, calandria coupling, position and size of the branchpoint)3机床主要部件结构图(主轴及工作台全套图纸、液压站全套图纸)Structure drawing of the main parts (drawing of the main axis, wor
9、kbench and hydraulic station)4专用件、易损件明细及图纸Details and drawings of the special parts and fragile parts5基础施工图(含承载、支承点、走管布线)Basic shop drawing (load, bearing point, wiring)6设备标准件、外购件清单、供货厂家及型号List of standardized parts and outsourcing parts, suppliers and type7电气/电子文件Electric/electron files7.1功能框图(包括动作
10、在循环中的顺序)Function block diagram (include order of the motion during the cycle)7.2强电全部图纸Drawings of the intense current7.3I/O模块图，接线板与外部的信息交换图I/O module, drawing of information exchange of patching board and outside7.4机床顺序图以及与外部的信息交换Precedence diagram of the machine tool and external information exchan
11、ge7.5所有电器配套件明细表(包括元件代号、型号规格、数量、生产厂家)Parts and components list for all device (element code, type and specification, quantity, manufacturers)7.6电柜、电箱、控制台的位置布置图Layout of electrical cabinet, electrical box and control panel7.7控制台图、故障与信息显示表Drawing of control panel, display table for diagnose and informa
12、tion7.8串行信号传递方式描述Description for serial signal convey7.9可编程控制器存贮器的组成和占有率，程序清单、可编程控制器和CNC数据Makeup and occupancy of programmable control memory, program list, programmable controller and CNC data.7.10电气控制系统(如CNC系统、伺服系统、PLC系统、电机、变频器等使用元器件)操作、链接、维修及 编程等全套中英版或英文版手册(如操作手册、维修手册、数控系统参数手册、数控系统编程手册、数 控系统系列交流伺
13、服电机参数手册及维修手册、其它外购件的操作维修手册等。Chinese-English pamphlets or English pamphlets (such as operation manual, maintenance manual, pamphlet for NC system parameters, programming pamphlet for NC system, pamphlet for AC servo electric motor parameters, manual for bought-in components, etc.) for electronic contr
14、ol system (eg: CNC system, servo system., PLC system, electric motor, transducer, etc.) specifying operation, link, maintenance and program, etc.7.11加工零件用CNC程序、PLC程序(梯形图且包含中文或英文注释)参数表、数据表以及具有正式授权的 自动编程PC软件、PLC编程软件SIMATIC STEP 7V5.3 incl. SP1(PC)、CNC与PC人机对话软件、网络支 持软件、编程操作说明书(中文或英文版)及于PC机的通讯电缆CP5512 P
15、CMCIA CARD及SIMATIC MPI KABEL。数控系统与BALLUFF读写控制器交换(通讯)程序。Processing parts uses CNC system, PLC system (trapezium written in Chinese or English) parameters, data and authorized PC soft, PLC programming soft SIMATIC STEP 7V5.3 incl. SP1 (PC), conversation soft of CNC and PC, network sup port soft, pamphlet for programming control (in Chinese or in English) and PC communication cables CP5512 PCMCIA CARD and SIMATIC MPI KABEL.NC system and exchanging (communication) program of BALLUFF read/write controller8液压、
