《焊条保温筒检定程序》由会员分享，可在线阅读，更多相关《焊条保温筒检定程序（10页珍藏版）》请在金锄头文库上搜索。
1、焊条保温筒检定程序文稿归稿存档编号： KKUY-KKIO69-OTM243-OLUI129-G00I-FDQS58-Rev. No版本1Page页6马1 of 6HY-MP-COP-002ProcedureNumber程序编号Document、一Status:文件状界PRE/港口 CFC/执行态:Reference procedure No. /Rev. /参考柱序编吁/版本：N/A 不适用Document Title 文件名称：Procedure for Calibration of Electrode Portable Oven焊条保温桶检定程序一Document Type/ 文件类型：M
2、anagement Procedure 管理程序Name &Title姓名及职务Signature/Date签名及日期Approved by批准Preparedby编制Reviewedby审核职务：Title :Signature/Date:签名及 日期QAReviewerQA审核Translato翻译Translation reviewer译审Copyright Declaration:版权声明：This docume nt is the property of the SNPEMC ? It must not be used, reproduced, transmitted or disc
3、losed without the prior written permission of SNPEMCo*齐口 i y ZrX 11. tir rH 4A- 4? hmi,出若 RF1/X -=1 +? TSTHlzIT八Fi Z,L 中 启 f 车|工仃Historical Records of Modification修改历史记录版本Rev发布日期Issue date修改范【书1及依据Scope and Basis of the Modification1A O ID1VI11 1Wl 1Table of Contents目录1. Purpose 目的This procedure def
4、ines the calibration method and management requirements for electrode portable oven to CV assembly and erection at HaiYang site ? 本程序叙述了焊条 保温筒的检定方法和使用管理要求。2. Scope范围This procedure is applicable for the calibration, using and managing of electrode portable oven of HaiYang CV Project of SNPEMC?本程序适用于S
5、NPEMC海阳CV项目焊接生产过 程中焊条保温筒的检定、使用和管理工作。3. Reference Documents 参考文件Quality Assurance Manual for Haiyang ProjectHY-QAM海阳项目质量保证手册HY-QAM4. Responsibilities 职责4.1 Engineering Department 工程夸B4. 1. 1 Shall prepare electrode portable oven requirements planning according to production demands:根据生产需要，编制焊条保温筒需求计划
6、；4? 1? 2 Use electrode portable oven correctly.正确使用焊条保温筒。5. 2 Material Section 物资组4? 2.1Be responsible for procure electrode portable oven and build up calibration records for portable oven.采购焊条保温筒，并建立焊条保温筒标定状态台帐。4? 2.2Be responsible for the periodical calibration, management and maintenance of elec
7、trode portable oven.负责焊条保温筒进行定期的标定、管理和维护。6. 2.3Be responsible for pasting right qualification label on portable oven according to appendix 6 in Procedure for Welding Haterial Contro1 ?按焊接材料控制程序附录 6 的 要求在保温桶上粘贴正确的标签。4. 3 QC Section QC部4. 3.1 Sign off the calibration records of electrode portable oven
8、.对焊条保温筒检定记录签字确认；4.3.2Be responsible for inspection of the qualification labels: supervise the usage ofelectrode portable oven.检查焊条保温筒上粘贴合格证，对焊条保温筒的使用情况进行监督。5. Calibration steps 标定步骤5.1 Check of prerequisites/ 检查先决条件5? 1.1 Power supply (24V or 36V) , calibrated thermometer, record form;电源(24V或36V)、标定
9、合格的温度计，记录表格；5? 1. 2Qualified operator and QC personnel:合格的操作人员和质检人员。5. 2 Temperature measuring method/ 温度测量方法5. 2.1 Switch on power supply for electrode portable oven (24V 或 36V);接通保温筒电源(24V或36V):5? 2.2The total measuring time is 1 hour, filling in the records every 20 minutes;测量时间为1小时，每间隔20分钟记录；5?
10、2.3The readings of measured temperature shall be within the range of 80? 150C, thetolerance is Ct 10 所测温度读数应在80? 150 C范围内，温度范围 10C:。5.3 Disposal of results/ 结果处理5? 3.1 The electrode thermostats shall be replaced or repaired if they are disabled在检定过程中，如发现保温筒不能达到使用要求应及时更换、修理；5? 3.2QC shall sing on the
11、 eligible calibrated portable oven, and confirm the acceptance label has been pasted on portable oven.QC在检定合格的保温筒标定记录上签字，并监督物资组在标定合格的保温筒外壁贴上合格标签。6. Regular Inspection of Portable Oven During Construction焊条保温桶在 使用过程中的检查6.1 General Requirement 通用要求6. 1? 1 Electrode portable oven will be inspected duri
12、ng welding construetion.焊条保温桶在焊接施工的全过程中要对其温度进行检查。6. 1.2Portable oven shall be inspected prior to putting electrodes into it. These electrodes can only be put into it after the temperature are confirmed ?在焊条放入保温桶时应第一次对保温桶进行温度检查。确保温度在规定范围后方可将焊条放入。6. 1.3Temperature after electrodes placed into portable
13、 oven shall be spot-checkedevery two hour by QC inspector, and results shall be recorded ? See section 7 for record sheet?焊条放入保温桶后每隔2小时由QC人员对其温度进行一次抽查。抽查个数应占总使用个数的50%或以上。检查结果形成记录，记录表格见第7部分。7. 1.4After construction, if there are some left electrodes, then the internal temperatureof portable oven shal
14、l be checked before return.焊接施工结束后，如果保温桶还有乘U余未用完的焊条，则应在归还前对内部温度进行一次检查。8. Applicable forms 适用表格Inspection Record for Electrode Portable Oven/ 焊条保温桶温度检查记录 (Sample)Inspection time 检查时 问(Y/M/D&XX;XX)Portable Oven Calibration NO.保温桶标定编号Actual temperature实测温度Remark备注No of Thermograph 温度计编号Operator 操作员：QC Inspector/QC 检查员：
