《鞋类一般缺点ok》由会员分享，可在线阅读，更多相关《鞋类一般缺点ok（9页珍藏版）》请在金锄头文库上搜索。
1、Raw material 原材料Color Variation 色 差Material stained 材料有污染Incorrect number of holes per inch square 网布目数不对Color variation of the same patch/roll 同卷色差Color variation of different patches/rolls 不同批次有色差Bottom color appear 露底色The skin peels off 脱层Stretching direction not correct 延伸方向 不对Elon gati on rate
2、is too much 材料延伸率太 大Yellowing 变黄Color fading away 褪色Color migration 溢色Too many blood vessel 血筋太多Too many scars 伤痕太多Too long /short hairy 毛太长/太短Defects of surface 表面瑕疵Get mildew 发霉Cracks of surface 表面有裂痕（龟裂）Thickness not meet the standard 厚度不 合标准Not dyed through 没透染Incorrect size of the material 大小规格
3、不 正确Lace length inconsistence 鞋带长度不一 Lace tip broken/open 鞋带包头裂开The paint of the lace tip peel off 鞋带包 头掉漆Metal eyelet surface not smooth 眼扣有 凸疤Incorrect side of material lamination 贴 合材料贴错面Leather brittle/breakable 真皮太脆Poor cement of hot melt 热溶胶不粘Velcro substandard 魔术带不良Aging test fail 老化不过Incorre
4、ct material emboss 皮料纹路不对 Foam yellowing 泡棉黄变Uneven stitching 车线不顺Flexing test failed 耐挠不过Gore too weak 松紧带弹性不佳Substandard Injection logo 射出 LOGO 不良Too stiff 太硬Too soft 太软Too narrow 太窄Too wide 太宽Too long 太长Too short 太短Too thin 太薄Too thick 太厚Cutting Procedure 裁剪Wrong material cutting 用错材料Wrong cuttin
5、g dies 用错裁刀型号Wrong size 用错码数Wrong positi oning of cutt ing dies 排刀错 误Too many layers may result in different specification of components, cutting failure, slip of cutting dies, distortion or jam of perfs. 裁层过多会导致部件有大小、 裁不断、滑刀、冲孔易变形、冲孔堵塞Failing on pairing by sticking matchinglabel 流水标配对错误Cutting dies
6、 are not sharp enough 裁刀 不锋利Cutting board becomes harsh due to long time of use 裁板使用过久表面不平顺Size label peel off after oven treatment 尺码 标烘箱后有脱落现象Incorrect size label 尺码标烫印错误Improper screen printing 网印线印不准Out sourcing 发外Material burning 材料打火Difficult to weld on material 不能热切Off position 错位Printing pee
7、l off 油印会掉Poor Printing Ink 油墨不良Unclear printing 印刷不清晰Unclear HF emboss/deboss 高周波（凸凹） 不明显Material stained after HF embossing/debossing 压高周波 （凸凹 ）污 染Golden foil peel off 烫金脱落Mesh is too opened to b printed 材料网 格太大，不能印刷Material shrink after printing 材料印刷后 收缩Material shrink after heat pressing 材料 热压后收
8、缩Material stained after printing 材料印刷 污染Material shrink after laser 材料镭射后收 缩Laser is too deep 镭射太深Material stained due to laser 镭射污染材 料表面Material surface burnt after laser 镭射烧 焦表面Laser off position 镭射位置对不上Embroidery thread broken 电绣断线 Embroidery needles quantity not enough 电绣太稀Embroidery needles qua
9、ntity too much 电绣太密Wrong embroidery thread 电绣线绣错 Embroidery thread too loose 电绣线太松 Embroidery thread too tight 电绣线太紧 Out sourcing component can not match with the proofread gauge 发外部件与校 正版对不上Material stained after chromed 电镀表面 有污染Chrome peels off 电镀表层脱落Poor chrome effect 电镀效果太差Chrome cracked 电镀表层龟裂F
10、low mark on TPU injection piece TPU 射出实物有流痕TPU injectio n piece sta in ed TPU 射出实物 有污染TPU injection piece shrink 射出实物有收 缩Bubbles on laminated material 贴合材料 有气泡Wrong stretch direction on laminated material 贴错延伸方向Poor bonding on laminated material 贴 合拉力不够Laminated material off shape 贴合材料 变形Stitching 针
11、车Too much hot melt cement 喷胶太多 Too less hot melt cement 喷胶太少 Cement comes out 溢胶Wrinkle 打皱Air cavity 包风X-ray 起鼓Improper marking 划线不标准Stitching exceed the stitching mark 盖 线太深Stitching not reaching the stitching mark 盖线太浅Foam positioned incorrectly 泡棉移位 Cement not thoroughly dried 胶水未干 Folding of sti
12、tch & turn rebounded after hammering 捶平后开骨位反弹Folding inconsistent 折边不圆顺Folded too much 折边太深Folded not enough 折边太浅 Inconsistent binding 包边不均匀Inconsistent piping 滚边不均匀Zigzag too loose 拼缝太松Zigzag too tight 拼缝太紧Too many backward stitches 倒针太多 Overlap stitches not overlapped properly 重针不对位Bottom thread a
13、ppears on upper 底线浮 珠Stitch without bottom thread 跳针 Needle broken 断针Stitchingdistance/margininconsistence 针距/边距不均Stitching holes too big 鞋面针孔太大Wrong needle 针车用针不对Wrong thread 针车用线不对Off center 中心车歪Collar top inconsistent 领口不圆顺Poor adhesive between collar and foam 领口与泡棉粘不死Lasting margin lock stitchin
14、g too high 压边线过高Lasting margin lock stitching too low 压 边线过低Toe gathering too tight 缩鞋头太紧Thread ends not clearly trimmed 线头没 修干净Lining not trimmed well 内里修边不良 Inconsistent collar stitching 压泡棉线不 圆顺Tongue joint too much 鞋舌接深Tongue joint not enough 鞋舌接浅Eyestay hole poorly punched 鞋眼孔冲孔 不良Leather damag
15、ed during stitching 皮料 在针车时损伤Eyelet got off 打扣松脱Eyelet painting peel off during pressing 打扣时扣子掉漆Eyelet broken after pressing 打扣后扣子 裂开Components wrong size attachment 部 件配错码数Medial and lateral stitching mixed up 内 外腰车错Left and right foot stitchi ng mixed up 左右脚车错Incorrect size label stitched 尺码标车错 Incorrect tongue stitched 上错鞋舌Bottom Unit Production 底生产Rubber outsole color bleeding 大底溢色 Rubber outsole inadequate cure 大底没 烧熟Rubber outsole over cured 大底烧太熟 The feather edge is too thick 大底水口太 厚Rubber outsole trimming not clear
