爱德利MS系列变频器使用说明书

上传人:桔**** 文档编号:485941321 上传时间:2023-05-26 格式:DOC 页数:73 大小:7.23MB
返回 下载 相关 举报
爱德利MS系列变频器使用说明书_第1页
第1页 / 共73页
爱德利MS系列变频器使用说明书_第2页
第2页 / 共73页
爱德利MS系列变频器使用说明书_第3页
第3页 / 共73页
爱德利MS系列变频器使用说明书_第4页
第4页 / 共73页
爱德利MS系列变频器使用说明书_第5页
第5页 / 共73页
点击查看更多>>
资源描述

《爱德利MS系列变频器使用说明书》由会员分享,可在线阅读,更多相关《爱德利MS系列变频器使用说明书(73页珍藏版)》请在金锄头文库上搜索。

1、RADLEEPOWERINSTRUCTION MANUALGENERAL-PURPOSEINVERTERMS2-102 MS2-122THANK YOU VERY MUCH FOR YOUR PURCHASEOF ADLEE INVERTER MS SERIES.PLEASE READ THIS INSTRUCTION MANUALBEFORE INSTALLATION OF THE INVERTER.PREFACEThis general-purpose inverter made by ADLEE Powertronic., Ltd.Read this instruction manual

2、 throughly before operation.This manual will be helpful in the installation, parameter setting,troubleshooting, and daily maintenance of the AC motor drives. Toguarantee safe operation of the equipment, read the following safetyguidelines before connecting power to the AC drives. Keep this oper-atin

3、g manual handy and distribute to all users for reference.A. General Precaution1. There are some covers and shields on this inverter. Make sure all covers and shields are replaced befor operating this product.2. This manual may be modified when necessary because of improve- ment of the product or cha

4、nges in specification.3. Contact your ADLEE representative to order a copy of this manual, if your manual has been damaged or lost.4. ADLEE is not responsible for any modification of the product made by the user, since that will void your guarantee.B. Safety symbolsSymbols which may appear on the ma

5、nualWARNINGIndicates a potentially hazardous situationwhich, if not avoided, could result indeath or serious injury to personnel.!CAUTIONIndicates a potentially hazardoussituation which, if not avoided, mayresult in minor or moderate injury topersonnel and damage to equipment.-I-RECEIVINGCAUTION* Do

6、 not install or operate the driver which is damaged or has missing parts. Failure to observe this caution may result in personal injury or equipment damage.INSTALLATION!CAUTION* Lift the cabinet by the base. When moving the unit, never lift by the front cover. Overwise, the main unit may be dropped

7、causing damage to the unit.* Mount the driver on nonflammable material. (i.e. metal) Failure to observe this caution can result a fire.* When mounting units in an enclosure, install a fan or other cooling device to keep the intake air temperature below 45 . Overheating may cause a fire or damage to

8、the unit.INSTALLATIONWARNING* Only commence wiring after verifying that the power supply is turned OFF. Failure to observe this warning can result in an electrical shock or a fire.* Wiring should be performed only by qualified personnel. Failure to observe this warning can result in an electrical sh

9、ock or a fire.* Make sure to ground the ground terminal. Ground resistance : 100 Ohm or less. Failure to observe this warning can result in an electrical shock or a fire.- II -CAUTION* Verify that the driver rated voltage coincides with the AC power supply voltage. Failure to observe this caution ca

10、n result in personal injury or a fire.* Do not perform a withstand voltage test of the driver. It may cause semi-conductor elements to be damaged.* To connect a braking resistor, follow in APPENDIX A. Improper connection may cause the unit damaged or a fire.* Tighten terminal screws. Failure to obse

11、rve this caution can result a fire.* Never connect the AC main circuit power supply to output terminals U, V and W. The inverter will be damaged and invalidate the guarantee.OPERATIONWARNING* Only turn ON the input power supply after replacing the front cover. Do not remove the cover while current i

12、s flowing. Failure to observe this warning can result in an electrical shock.- III -!CAUTION* Since it is easy to change. Operation speed from low to high speed, verify the safe working range of the motor and machine before op- eration. Failure to observe this caution can resuit in personal injury a

13、nd machine damage.* Do not change signals during operation. The machine or the inverter may be damaged.* All the constants of the inverter have been preset at the factory. Do not change the settings unnecessary.MAINTENANCE AND INSPECTIONWARNING* Never touch high-voltage terminals in the driver. Fail

14、ure to observe this warning can result in an electrical shock.* Replace all protective covers before powering up the inverter. To remove the cover, make sure to shut OFF the molded-case circuit breaker. Failure to observe this warning can result in an electrical shock.* Perform maintenance or inspec

15、tion only after verifying that the CHARGE LED goes OFF, after the main circuit power supply is turnned OFF. The capacitors are still charged and can be dangerous.* Only authorized personnel should be permitted to perform mainte- nance, inspections or parts replacement. Failure to observe this warning can result in an electrical shock.- IV -CAUTION* The control PC board employs CMOS ICs. Do not touch the CMOS elements by hand. They are easily damaged by static electricity.* Do no

展开阅读全文
相关资源
相关搜索

当前位置:首页 > 大杂烩/其它

电脑版 |金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号