STANDARDS 参考标准：Refer to BIFMA X5.1-2021 ModifiedCustomer客户Menard-OD10112901Supplier工厂名称浙江群英车业 C007599Supplier Item No.工厂产品编号Refer to P/OTest Rite Item No. 特力产品 编号KCS778TUDescription产品描述STEEL STACKING TEXTILENE CHAIRCertification平安认证Refer to P/OSpec. Prepared By TR w/ Date 制定人及日期Allen 2021/1/26Spec. Checked By Supplier w/ Date工厂确认/日期Spec. Approved By Customer w/ Date 客户确认/日期Revision no 版本0TEST ITEMS 〔测试条款〕REQUIREMENTS (要求)FINDINGS (发现)1、 Cosmetic/Appearance外观以及特征***Appearance外观Sharp point/edge other than intended function. 非功能性尖边尖点P**Appearance外观Free of rust, splinters, cracks, running paints, scratch, and burrs, smell or other obvious defects. Edges and corners shall be rounded.P"Appearance外观Slightly visual defects of product or package. 轻微外观缺陷P**Feature of product产品特征With 1 1 TEXTILENEFrame with powder coatingOthers please refer to P/O and sample.P* 2、Dimension 尺寸Overall size总体尺寸550(W)+/-10mm x810(D)+/-15mm x940(H)+/-15mm545mm< 810mm< 940mmSize of leg tube 脚管尺寸42(W)+/-1.5mm M4(D)+/-1mmWin.0.8(T)mm42.2mmx 14.1mmx 0.84mmSize of back seat tube 椅背管尺寸26(W)+/-1mm x17(D)+/-1mmWin.0.9(T)mm26.7mmX 17.2mmx 0.96mmHeight of seating 椅囿局度420+/-10mm420mmDiameter of front leg cross bar前连结管尺寸28(W)+/-1mm x14(D)+/-1mm28.6mmx 14.3mmDiameter of back leg cross bar后连结管尺寸19(DIA)+/-1mm19.2mmDiameter of back seat cross bar靠背连结管尺寸10(DIA)+/-1mm10.1mmTotal weight 总重4.5kg+/-5%4.5kg** 3、 Construction 结构 & Assembly 组装Construction of product 产品结构There shall be no accessible shear and squeeze points created by loads applied during normal use.在承重卜止常使用过程中不能产生可接触到 的剪切挤压点。
PTubular components, holes and gaps accessible during use shall be covered if a 7mm or 12mm test probe can be pushed into them in any direction with a maximum force of 30N to a depth of more than 10mm and cannot be pulled out again in the reverse direction by a maximum force of 30N.使用过程中可接触的管状部件，孔洞和间隙 用7mm^ 12mmJ测试棒可以在任何方向以不 超过30N力推入超过10mm勺深度并且在反方 向以最大30N的力不能拔出的那么应该被覆盖PBottom of tubular legs shall be capped or plugged.管状脚的底部应该被覆盖或塞住PShall be no penetrating odor or fetor. 应没有剌激性气味及恶臭PNo missing or wrong parts or other structural defect.无遗漏或错误部件或其他结构上的缺陷。
PKeep stable on the level surface. 在水平面上应保持平稳P** 4、Performance 性能Performance of product 产品性能The actual usage of performance shall be conducted to meet intended purpose of product and basic requirement of consumer.产品应能达成设计的功能P5、Labeling； Marking & safety 标签，标识，女全要求**Marking 标识Refer to P/ONC**Labeling 标签Refer to P/OSee ending care and fabric content label** Safety平安要求Refer to P/ONC** 6、Test properties女全以及功能测试California 65 Regulation加州65法规A. Need test reportB. Need add warning label.需要贴加警告标签，标签内容如下。
"WARNING: This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm."NAMenards OD furnitureBack pull static loadNo failure at 100 lbs. for 1 minute applied to90 degrees from back at 16 in. above the seat.PSeat static loadNo structural failure under 500lbs. compression for 1 hour.P■ J浦!医2AL d■Font seating capacityNo failure under 300 lbs. loading at edge for 1 hour (6 In. from the front edge).pww& 11T\Arm strength verticalNo permanent deformation at 169 lbs. for 10 minutes. The vertical load is uniformly applied through a 5 in. area at the apparent weakest point.PfArm strength horizontalNo permanent deformation at 75lbs. for 1 minute. The load is applied to the arm rest horizontally at the most forward point of the arm rest area.PImpact durabilityNo structural breakage, deformation when 125 lbs. test load free - falls from 6 in. to the center of the article (10 drops).A test bag approximately 400mm (16 in.) in diameter containing sand and/or shot weighing 57 kg (125 lbs.)PLeg strength testNo failure at 75 lbs. applied to the leg at 1 In. from the end of the leg. Force is applied in four directions (forward, rearward, side and side). Hold for 1 minute.PRear stabilityBackrest in the furthest reclining position The chair shall be placed on a test platform. A block, obstruction or other restraining device 13mm (0.5 in.) in height shall be affixed to the test platform. Load the chair with 6 disks.Place the first disk on the seat so it touches the support fixture. As each disk is added to the stack slide it along the lower disk until it contacts the support fixture. As each disk is added, the backrest may move such that the lower disks do not remain against the support fixture; this is acceptable, do not reposition the disks. Apply a horizontal force to the highest disk. The location of the force application is 6 mm (0.25 in.) from the top of the disk. For chairs with seat height (as measured at the front of the bottom of the lowest disk。