《成型不良及分析》由会员分享，可在线阅读，更多相关《成型不良及分析（4页珍藏版）》请在金锄头文库上搜索。
1、1. 毛 ft(Flash)/(Burr)塑膝料溢出之料2. 疙 (Bloom)成形表面有粗糙粒状的现象A noncontinuous surface coating conming from additives in the plastic.3. 不施模 /缺料(Short Shot/Void)没有射出足豹的原料填满外模Injection of insufficient material to fill the overmold.Failure of plastic to completely fill mold cavity.4. 燎焦(Burns)熟量分解，通常典燮色(Discolora
2、tion )同畤畿生Thermal decomposition, usually with discoloration.5. 编水(Sink/ Shrink mark)表面巍裂，下沈或凹陷其原因是物没有同畤收编或被螺ffl住的材 Surface discontinuity , depression or dimple caused by non-uniform material shrinkage , or clamping of cable; depressions on a surface.6. 刮僵(Scratches)材料外暮晃表面走生藻槽的损僵Damaged outer surfac
3、e of jacket where material has been removed; Swallow grooves.7. 割泓Cut)外表面被一尖物品损僵Damaged outer surface of jacket by a sharp object.8. (Tooling Mark)使用夹子或工具修整材外被所造成的损僵。Deformity of cable jacket resulting from clamping or tooling.9. 合模富泉裂(Parting Line Split)因外模材收编、爆裂或破裂而走生外模分裂This is where the overmold
4、 material shrinks and cracks or splits, creating a tear in the overmold.Thin projection or material 90 degree to surface on a parting line.10. 熔合富泉(Weld/Knit Line)熔合是成形材料合流的部份，在成形品上以熔合痕出现。A visible line or mark on a surface.11. J真白(Clouding)成型品於项出黑占位置殛留白黑成象12. 污染(Contamination/Dirt/Blemish/Speck)墨水、
5、麟物、助焊蒯或其他外来物13. 色差 / 燮色(Color Difference/Discoloration)典原始色版之色有差巽Any change from original color or unintended, inconsistent part color.14. 脸斤裂(Brittleness)隔M.柱或卡导旬因受力(拉伸或捞摩)而新裂15. 阻塞(Fill in)Pin孔(同翰孔)因巽物而阻塞16. 摩痕(Pinch off)辰畤之摩力(重摩)造成之雁燮(外被凹陷)Any irregularly shaped, void or impression left on the ov
6、ermold, caused during preparation or handling.17. 燮形(Deformity/Deformation)零件受损或典外型不符Components is bent or show signs of deformation.18. 击黑占(Pimple)塑膝料内含颗粒物19. 凹黑占(Dimple/Pits)平面上的坑洞Small hollow/crater on a surface.20. 流痕(Flow Marks)外表面走生波浪或4条现象Wavy or streaked appearance of a surface.21. SR 彳慎斜(Til
7、ted Strain Relief)Cable should exit in a straight line from a connector assembly.22. 雾(Haze)成品於裂程中所造成表面有白雾状之现象Cloudiness on an otherwise transparent part.23. 逵料黑占遏深(Gates)指成形彳爰，逵料黑占有凹陷的现象24. 翘曲(Warpage)成形造成外鹭曲的现象25. 突出(Protrusion)A raised area on a surface(Blister, bump, ridge)26. 雅蜀Specks)Small par
8、ticles.27. 兼泡(Bubbles)Bubbles can be caused by not having uniform melt in the molding process.28. BlushDiscoloration caused by plastic flow during molding, usually found near gates.29. Gate Blush锥料黑占巽色)Discoloration around the gate area.30. 光潭度偏差(Glossiness)光潭度遏量或不足的部份面稹。An area of excessive or defi
9、cient gloss.31. 凹痕(Gouge)能被感知的刻或是凹陷(亚非编水所致)Indentation or dent that can be felt(not a sink mark)32. PorosityBlow holes, pits or underfills.32.Texture flowVariation or unevenness in texture.1. 毛ft (Flash)溢出稷ft之余料2. 燮形(Deformity)零件受损或典外型不符3. 摩僵(Pinch off)辰畤之摩力(重摩)造成之雁燮(外被凹陷)4. 脸斤裂(Brittleness)材受外力影警造成
10、破裂、新裂5. 氧化(Oxidation)令载材氧化或生鳞6. 刮僵(Scratches)材料外暮晃表面走生藻槽的损僵Damaged outer surface of jacket where material has been removed.7. 割泓Cut)外表面被一尖物品损僵Damaged outer surface of jacket by a sharp object.9.污染(Contamination/Dirt)墨水、麟物、助焊蒯或其他外来物1. 撅散(Over Plating)屑或物面稹超出言殳定原有面稹2. 燮形(Deformity)零件受损或典外型不符3. B (Pinc
11、h off)辰畤之摩力(重摩)造成之雁燮(外被凹陷)4. 露底材(Copper Exposured)屑未完全包覆被物表面之底材外露5. 缺料(Short material)6. 剥金(Plating missing)屑受外力条件影警吏屑典被物表面分雕或脱落7. 兼泡(Bubbles)导旱在兼髓尚未完全排除前即已凝固，而形成此冏题。8. 黑黑占(Black drop)屑表面因外来物附著或氧化腐食虫之黑色斑黑占9. 导旱黑占表面粗糙导旱黑占表面成砂状，突出表面10. 氧化(Oxidation)令载材氧化或生鳞11. 游(Nodules)12. 漏敏Skip plating)13. 粉矣工圈(Pink ring)14. 屑破洞(Plating voids)15. 屑太薄(Thin plating)
