《阳泉三矿3.0 Mta新井设计双巷掘进副巷采动变形规律的数值模拟研究》由会员分享，可在线阅读，更多相关《阳泉三矿3.0 Mta新井设计双巷掘进副巷采动变形规律的数值模拟研究（147页珍藏版）》请在金锄头文库上搜索。
1、中 国 矿 业 大 学本科生毕业论文姓 名： 学 号： 学 院： 矿 业 工 程 学 院 专 业： 采 矿 工 程 论文题目： 阳泉三矿3.0 Mt/a新井设计 专 题： 双巷掘进副巷采动变形规律的数值模拟研究 指导教师： 职 称： 教 授 2011 年 6 月 徐州中国矿业大学毕业论文任务书学院 矿业工程学院 专业年级 采矿工程07级 学生姓名 任务下达日期：2011年1月14日毕业论文日期：2011年3月14日至2011年6月9日毕业论文题目： 阳泉三矿3.0 Mt/a新井设计毕业论文专题题目：双巷掘进副巷采动变形规律的数值模拟研究毕业论文主要内容和要求：根据采矿工程专业毕业设计大纲，本设
2、计包括一般部分、专题部分和翻译部分，具体包括：1、以阳泉三矿条件为基础，完成阳泉三矿3.0Mt/a新井设计。主要内容包括：矿井概况、矿井工作制度及设计生产能力、井田开拓、首采区设计、采煤方法、矿井通风系统、矿井运输提升等。2、结合实习矿井实际情况或当前煤矿生产前沿，撰写一篇专题论文。3、完成近3-5年国外期刊上与采矿或煤矿安全有关的科技论文翻译一篇，要求不少于3000字符。院长签字： 指导教师签字：摘 要本设计包括三个部分：一般部分、专题部分和翻译部分。一般部分为阳泉三矿3.0 Mt/a新井设计。一般部分共包括10章：1.矿区概述及井田地质特征；2.井田境界和储量；3.矿井工作制度及设计生产能
3、力、服务年限；4.井田开拓；5.准备方式-带(盘)区巷道布置；6.采煤方法；7.井下运输；8.矿井提升；9.矿井通风与安全技术；10.矿井基本技术经济指标。阳泉三矿位于阳泉矿区的西部，距阳泉市中心7.5公里，交通便利。井田形状近似长方形，东西长约7.6 km，南北宽约3.0 km，面积约21 km2。井田内开采15#和3#煤层，先采15#，做为解放层开采，后开采3#煤。煤层倾角28，局部地区10，平均5。煤层平均厚度3#煤层3.5 m，15#煤7.5 m。井田地质条件较为简单。矿井工业储量为330.2297Mt，可采储量为220.6853Mt。矿井设计生产能力为3.0Mt/a。矿井服务年限61
4、.3 a。矿井涌水量不大，正常涌水量为50 m3/h，最大涌水量为100 m3/h。15#煤相对瓦斯涌出量为4 m3/t，属低瓦斯煤层。矿井煤尘无爆炸危险性，煤层不易自燃，自然发火等级为级。矿井采用立井两水平开拓，上行开采。一矿一面，采煤方法为综合机械化放顶煤开采。全矿采用胶带运输机运煤，辅助运输前期采用1.5 t固定箱矿车，后期采用齿轨车运输。矿井通风方式前期为中央并列式，后期根据需要在井田东西两翼增加两个边界风井。矿井年工作日为330 d，日净提升时间16 h，工作制度为“四六制”。专题部分题目是双巷掘进副巷采动变形规律的数值模拟研究。以阳煤集团新大地煤矿为例，通过使用UDEC数值模拟软件
5、进行分析计算，模拟了15202工作面开采后，不同尺寸煤柱条件下进风副巷与进风巷之间煤柱的应力与变形的演化规律，以及不同尺寸条件下进风副巷的应力、变形的演化规律，得出双巷掘进时副巷受采动变形的基本规律以及煤柱尺寸的合理留设。翻译部分是一篇深部煤与瓦斯突出矿井危险等级的分类技术的论文，英文题目为Classification technique for danger classes of coal and gas outburst in deep coal mines.关键词：立井开拓； 带区； 综合机械化放顶煤开采； 蓄电池电机车运输 ；混合式通风ABSTRACTThis design inclu
6、des three parts: the general part, special subject part and translation part.The general part is a new design of NO.3 of Yangquan mine. This design includes ten chapters: 1.An outline of the mine field geology; 2.Boundary and the reserves of mine; 3.The service life and working system of mine; 4.Dev
7、elopment engineering of coalfield; 5.The layout of mining area; 6.The method used in coal mining; 7. Transportation of the underground; 8.The lifting of the mine; 9. The ventilation and the safety operation of the mine; 10.The basic economic and technical norms.No.3 of Yangquan mine locates at the w
8、est of Yangquan Mine area, 7.5 km away from the center of the town. And it has convenience transportations. The shape of minefield is like a rectangle which has a length of 7.6 km in the east and west direction while a width of 3.0 km in the south and north direction on average. The total area is Ap
9、proximately 21 km2. There are mainly two coal seams in the mine 3# and 15#. First mining15# seam upstream mining.The average angle is 5 degree, while the thickness is about 7.5 m. The minefield geological condition is simple.The proved reserves of the minefield are 330.22million tons. The recoverabl
10、e reserves are 220.68 million tons. The designed productive capacity is 3.0 million tons per year. The service life is 61.3 years. The normal flow of the mine is 50 m3 per hour and the max flow of the mine is 100 m3 per hour. The Relative gas discharge quantity is 4 m3 per ton. Thus it is Low gaseou
11、s mine. The coal dust of the mine has non-explosion hazard. And the coal seam is hardly spontaneous combustion. The level of spontaneous combustion is .The development of the mine is double level with two vertical shaft. The number of the working faces is only one. Comprehensive mechanization puts i
12、n the top coal technology is the mining method. Several belt conveyers undertake the job of coal transport in the mine, while the auxiliary transportation system depends on the mine cars. The ventilation type in the early stage is centralized juxtapose. In the late stage two air shafts in the bounda
13、ry should be driven. The ventilation method is extraction.The working days in a year are 330. Everyday it takes 16 hours in lifting the coal. The working system in the mine is “four-six”.The title of the special subject part is “Deputy Lane dual roadway Mining Numerical simulation of deformation”. B
14、y using the UDEC analysis of numerical calculation simulation software to simulate the 15202 working face, the Pillar of different sizes into the air inlet Lane, Deputy Lane and between the stress and deformation of coal pillar The evolution law, and under conditions of different sizes, Deputy Lane,
15、 wind stress, the evolution of deformation is obtained when the dual roadway deformation, Deputy Lane by the basic law of mining and the left pillar set a reasonable size, with similar conditions Roadway reference.The translated academic paper is about classification technique for danger classes of coal and gas outburst in deep coal mines. Its title is “Classification technique for danger classes of coal and gas outburst in deep coal mines”.Keywords: vertical shaft development; strip district; comprehensive mechanization puts in the t
