《塑胶件验收质量检验规范(精)》由会员分享,可在线阅读,更多相关《塑胶件验收质量检验规范(精)(7页珍藏版)》请在金锄头文库上搜索。
1、精品范文模板 可修改删除撰写人:_日 期:_技术质量保证协议 附件 塑胶件验收质量检验规范买方: 卖方: 一、 本规范基于买方相关移动电话外观检验标准、来料检验规范、系统实验室来料实验方案、手机成品测试规范、卖方产品规格书、质量检验标准以及相关国家标准、行业标准制定。二、 适用范围本规范适用于卖方提供给买方的塑胶件检验,买方使用本规范进行塑胶件来料检验。三、 抽样方案与判定标准3.1 抽样方案采用GB/T2828.1-2003/ISO2859-1:1999抽样标准中的正常检查一次抽样方案。3.2 判定标准3.2.1 缺陷项目分类A、致命缺陷CRI(Critical Defect)项目规定:明显
2、且会造成伤害的浇铸口切断,明显且会造成伤害的缩水痕和毛刺。B、主要缺陷MAJ(Major Defect)项目规定:断裂、裂缝、弯曲变形、脱漆、严重划伤、影响装配的缺陷等。C、次要缺陷MIN(Minor Defect)项目规定:脏污、轻微划伤、黑点、亮点等。3.2.2检查水平和接收质量限(AQL)规定致命缺陷不允许出现主要缺陷次要缺陷装配、外形尺寸、和特殊性能(导电漆)检测检查水平S-1接收质量限AQL=2.5外观检测检查水平II接收质量限AQL=0.65四、 检验要求4.1 外观要求检验时应在光源为普通室内40W日光灯的照明环境下,且光源距离待测物1m,以非透光方式,让眼睛与待测物距离30cm
3、 , 目检方向与待测物成4590度(视线与待测面垂直为90度),检验时每面检验不超过10秒,以目视扫描方式进行。4.1.1尺寸、公差符合设计图纸要求。4.1.2颜色与双方承认的色度样版为据检测。4.1.3各结构件上图案、文字应正确。无印刷缺陷,诸如:印刷倾斜,毛边,宽窄不一致,文字重叠,字体印刷不全,文字偏移等 。4.1.4边、角位置应无注塑、喷涂毛刺,或者因此缺陷引起的脱漆。4.1.5按键字符印刷在结构件上的特殊结构件,应对光检测结构件无漏光现象。4.1.6外观必须满足如下外观检验标准,见附表一。附表一:外观检验标准类别(Class)定义及項目(Definition & Item list)
4、A使用时主要面可视区域Primary surface exposed to direct close-up view in ordinary use项目:前壳 ,翻盖Item: upper case, flipper.B使用次要面可视区域Secondary surface exposed but not in direct view in ordinary use项目:塑胶件的侧面、电池面壳所暴露之区域Item: plastic part of side;outside battery when using. C使用时不可视的区域Surface not visible in ordinary
5、use项目:后壳与电池结合面Item: D-cover surface which touch to batteryDescription描述Item项目Criteria 标准Defect Classification故障分类长度L(mm)宽度W(mm)距离D(mm)数量N接受AccMinMajCriStraight line &Curve (Flow Mark, Scratch)直线和曲线(波纹,划伤)A20.052022L40.05140.11X40.11XB15L3W0.0520250.1150.11X50.11XC2L50.0520270.1170.11X70.11XWeld line
6、缝隙线A40.0520260.05160.11X60.11XB50.0520270.1170.11X70.11XC100.05202100.11100.11X100.11XDescription描述Item项目Criteria 标准Defect Classification故障分类直径(mm)距离D (mm)数量N接受AccMinMajCriBlackSpot Dust,Light Spot, Contamination, Dent Mark黑点,灰尘,亮点,污染物,凹痕A0.22020.20.310.30.51X0.51XBDefect of similar color 同色点0.250.4
7、2020.40.51Defect of different color 异色点0.10.252020.351CDefect of similar color 同色点0.40.72020.70.910.91.21X1.21XDefect of different color 异色点0.350.52020.50.710.70.91X0.91XPhone cover peels off in drop test 在跌落试验中手机盖子脱落XAntenna天线Antenna fixes tightly, gap between antenna and housing0.15mm天线安装牢固,天线接缝0.
8、15mmStep between antenna and housing 0.2mm 天线台阶错位0.2mmXThere are so many defects that could not be assembled 有很多缺陷造成无法装配的XKeypad gap按键缝隙ABbetween keypad and upper single gap0.2mm 按键和前壳单边缝隙不超过0.2mm 0.4mm Between keypad and upper single gap 0.6mm按键和前壳的单边缝隙大于0.2mm但不大于0.4mmXKeypad and upper single gap0.
9、4mm 按键和前壳的单边缝隙大于0.4mmXUpper & Lower housing前、后壳Gap between upper housing and lower housing0.6mm(width of art design line is 0.4mm0.5mm)前壳与后壳的缝隙0.6mm(美工线宽度为0.40.5mm)Gap between upper housing and lower housing0.25mm(except art design line)前壳与后壳的缝隙0.25mm(不包含美工线)Lens护镜Lens assembly gap 0.3mm 护镜装配后缝隙0.3m
10、m(单边0.15mm)0.3mm Lens assembly gap 0.5mm 0.3mm护镜装配后缝隙0.5mmXLens assembly gap 0.5mm 护镜装配后缝隙0.5mmXAssembly gap装配缝隙Battery电池Can not open & close不能打开或扣上XBattery & Lower housing assembly gap0.3mm电池与后壳的缝隙0.3mmBattery Locking Knob has a problem, but no effect for use电池扣有缺陷,但不影响使用XBattery Locking Knob has a
11、 problem and affect use电池扣有缺陷,影响使用XWhen did assembly, right and left movable gap0.2mm装配后,左右移动的缝隙0.2mmStep gap between battery and lower housing0.15mm电池与后壳间的错位0.15mmWhen did assembly, up and down movable gap0.3mm装配后,上下移动的缝隙0.3mmI/O connectorI/O接口Gap between I/O connector and housing0.3mmI/O接口和前后壳间隙小于等于0.3mmStep gap in Assembly错位Upper& lower housing前、后壳Step gap0.1mm前后壳错位小于等于0.1mm0.1mm Step gap 0.2mm前后壳错位大于0.1mm但不大于0.2mmXStep gap 0.2mm前后壳错位大于0.2mmXLCD housingLCD里、面壳Step Gap between LCD housing0.2mm翻盖里、面壳之间的错位小于等于0.2