《西门子吸嘴日常保养及预防性管理》由会员分享，可在线阅读，更多相关《西门子吸嘴日常保养及预防性管理（12页珍藏版）》请在金锄头文库上搜索。
1、WORK INSTRUCTION作 业 指 导 书REVISION / 版本号:01DOC. NO. / 文件编号:PRODUCT / 产品: All PAGE/页数: 11 Of 11TITLE / 标题: SIPLACE Nozzles Cleaning & preventive management 西门子吸嘴日常保养及预防性管理 WORK INSTRUCTION作 业 指 导 书DOC. No. / 文件编号:FIEEI-075REV./ 版本号:01PRODUCT/ 产品:AllTITLE / 标题: SIPLACE Nozzles Cleaning & preventive man
2、agement 西门子吸嘴日常保养及预防性管理PAGE/页数 1 OF 11REVISION HISTORY / 版本记录REVISION 版本CHANGE DESCRIPTION 修改内容ISSUER发布者RELEASE DATE发行日期REMARK备注APPROVALDEPARTMENTNAMETITLE部门名字职位1.0 PURPOSE目的Provide good & cleaning nozzle for production line to reduce the product quality issues and machine down time caused by nozzle
3、 problem.确保为生产线提供优质清洁的吸嘴，减少因吸嘴问题造成的产品品质问题和停机时间2.0 SCOPE范围This procedure is Applicable for XJDZSMT Siemens placement equipment. 本规程适用于XJ电子大楼一楼SMT西门子贴片设备。3.0 DEFINITIONS/定义3.1 SMT- Surface Mount Technology 表面贴装技术3.2 PM Preventive Maintenance 预防性保养4.0 RESPONSIBILITY 职责4.1 SMT engineer is responsible to
4、 compile WI, establish nozzle PM and management procedure to direct PM team to progress the activity.SMT 工程师负责编写指导书，制定吸嘴保养和管理程序。指导技术员和保养人员进行吸嘴保养。4.2 SMT PM Team is responsible for the detailed PM activity.SMT 保养人员负责执行具体的保养行为。 4.3 Machine operator feedback the machine running information to engineer
5、& technician timely. We are all responsible for our equipment.机器操作员及时向工程师和技术员反馈机器的各种运行信息，做到：我们所有人对我们的设备负责。5.0 EQUIPMENT/TOOLS 仪器/工具5.1 Cleaning appliance for nozzle series 60x, 70x/90x, 1x0x. 吸嘴清洁器具。5.2 Nozzle brush (8mm) with brush size0.1mm 吸嘴刷子5.3 Ultrasonic bath with minimum 20 minutes runtime a
6、nd a minimum size of L = 85 / B = 50 / D = 25 mm.超声波清洗柜5.4 Lint-free cloths 无尘布5.5 Ethyl alcohol 普通酒精5.6 Compress air 压缩空气5.7 Magnifying glass / Microscope 放大镜 / 显微镜6.0 PROCEDURE 步骤6.1 Remove the nozzle from machine. 从机器上将吸嘴拆除。For ceramic nozzle / 针对陶瓷吸嘴6.2 Filling the cleaning appliance. 将吸嘴放置到清洁器中
7、。6.2.1 Turn the wing bolt (90/to the left) in order to loosen the top part of the block.将旋钮向左转90度或0度，松开锁住的顶盖。6.2.2 Separate top and bottom part. 将上盖和底座分开。 6.2.3 Insert the ceramic nozzles (color coding headfirst) into the location hole of the top part.将陶瓷吸嘴摆放到清洁器的孔中。（如图所示，有颜色条码的一端朝上。）6.2.4 Place the
8、 bottom part onto the nozzle tip, inner side facing downward.将底盖盖上，内表面朝下。.6.2.5 Turn the wing bolt (90/to the right) and interlock both parts.向右旋转旋钮，将上下盖锁上。6.3 Cleaning without Ultrasonic Bath. (In case of strong pollution, e.g. with soldering paste, cleaning without ultrasonic bath is not sufficien
9、t)不用超声波清洗柜。（如果污染严重，比如锡膏污染，这时不用超声波是清洗不干净的。）6.3.1 Dip nozzle brush (8mm) into cleaning liquid. 用刷子(8mm) 蘸取清洗液。6.3.2 Place nozzle brush (8mm) into grooves of the cleaning appliance and remove contamination: clean with small upward movements (of app. 3-5mm), apply slight pressure only.将毛刷放在清洗器的凹槽中，轻轻的来回
10、刷洗，去除吸嘴的污染物。(Strictly avoid any contact of nozzle tips with the metal core of the brush.严禁用毛刷的金属部分接触吸嘴头部。)6.4 Cleaning with Ultrasonic Bath/用超声波柜清洗6.4.1 Insert cleaning appliance, nozzle tips pointing downward, into ultrasonic bath.将吸嘴清洁器按照吸嘴头部朝下的方向放进超声波柜。6.4.2 When ultrasonic time sequence is over,
11、 turn appliance so that nozzle tips point upward.超声波清洗时间结束后，将清洗器翻转吸嘴头部朝上放置。6.4.3 Place nozzle brush (8mm) into grooves of the cleaning appliance and remove contamination: clean with small upward movements (of app. 3-5mm), apply slight pressure only.将毛刷放在清洗器的凹槽中，轻轻的来回刷洗，去除吸嘴的污染物。（同上6.3.2）6.5 After-cl
12、eaning 清洗以后6.5.1 Rinse cleaning residues from nozzles and cleaning appliance with tap water.用水冲洗清洗器去处吸嘴上的残留物6.5.2 Degrease appliance and nozzles using a lint-free cloth moistened with ethyl alcohol.用无尘布蘸取酒精清洁吸嘴和清洁器上。6.5.3 Use compressed air to blow clean the nozzle appliance from top and bottom.用压缩空
13、气清洁清洗器的上面和底面。6.6 Use a magnifying glass or a microscope to check the suction area of the nozzles. Re-clean nozzles if first cleaning was not satisfactory and replace all defective nozzles.用放大镜或显微镜检查吸嘴吸气部分。如果清洗效果不好需要重新清洗并更换坏的吸嘴。6.7 Check the nozzles for correct cleaning result.确认吸嘴清洗效果。For plastic nozzle / 针对塑胶吸嘴6.8 Plastic nozzle can not be cleaned by ultrasonic+. 塑胶吸嘴不能使用超声波加酒精清洗。6.9 Follow up the process from 6.2 6.3.执行6.2到6.3的清洗步骤。6.10 Follow up
