《JT-04D说明书英文》由会员分享，可在线阅读，更多相关《JT-04D说明书英文（32页珍藏版）》请在金锄头文库上搜索。
1、 真诚为您提供优质参考资料，若有不当之处，请指正。Jinbo Intelligent IC Card Elevator SystemInstallation & Operation ManualHebei Jinbo Intelligent Elevator Equipment Co., Ltd.Telephone: 86-311-85380096 Fax: 86-311-85380097 / CatalogI. SYSTEM INTRODUCTION3II. SYSTEM CONFIGURATION3III. TECHNICAL PARAMETERS FOR MASTER CONTROL P
2、ART OF SYSTEM3IV. FUNCTION INTRODUCTION3IX. INSTALLATION INSTRUCTIONS11X. SYSTEM DEBUGGING14XI. TREATMENT OF COMMON FAULTS15XII. POINTS FOR ATTENTION16XIII. FUNCTIONS OF CARDS16XIV. OPERATING INSTRUCTIONS & VOICE PROMPT OF CARDS17XV DESCRIPTIONS OF ELEVATOR NUMBER AND OFFICE NUMBER18I. System Introd
3、uctionElevator IC card management system can realize the computer intelligent control and management of elevator passenger, which prevents miscellaneous personnel from using the elevator arbitrarily to come in and go out the building effectively and thus improves the safety management of the buildin
4、g.Every passenger can get a card from the management center and each passenger shall take the elevator by card with specified authority. The arrival floor of each card shall be designated by the property management department when the card is issued. The cardholder can only press key for selecting p
5、arking floor, call landing and park at arrival floor on designated floor; and the cardholder can neither call landing nor park on non-designated floor.The system, which can only change the floor selection authority function of elevator, can not change the running function of elevator. It adds manage
6、ment function based on the original functions of elevator. It adopts contactless IC card control and the content of the card occupies two sectors in the card, so it can share one card with other systems to realize the regional all-purpose card function.II. System ConfigurationThis system consists of
7、 hardware and soft ware. The hard ware includes main controller. Card antenna, power supply, smart card device, IC card etc. which constitute car call control system, and the software part consists of control software for running of subordinate computer and licensed software for card writing of host
8、 computer.III. Technical Parameters for Master Control Part of System1. Input voltage: DC12V36V2. Input current: 70mA3. Input voltage of manual and fire fighting ports: DC12V24V4. Output point of car call master control panel: channel 25. Features of the output point: switch output6. Service tempera
9、ture: -1060, and the humidity of working environment is RH 30% 95% without moisture condensation7. Storage temperature: -20708. Operation time for swiping card: 100ms9. Communication distance of radiofrequency: 20,000 hours15. Mean maintenance time: 0.5 hourIV. Function IntroductionThe system is cha
10、racterized by compact structure and powerful functions. It can realize interchange function of charged card swiping and non-charge card swiping, mandatory management function, fire fighting and manual switch function, card-swiping switch function, reporting function for lost card.1. Fire Fighting Fu
11、nctionThe system itself has fire fighting function, in case of disasters such as fire or earthquake in the building, the system will separate itself from control and revert to service state without need to swipe card as the fire fighting function of the elevator is enabled.2. Manual Switch FunctionT
12、hrough the switching of manual switch, this system can realize the interchange between the non-swiping card and swiping card when using the elevator.3. Card-swiping Switch FunctionThrough swiping key card in the card-reading zone, it can realize the interchange between unlocking state and state of t
13、aking elevator by swiping card of elevator system.4. Mandatory Management FunctionThrough swiping the mandatory management card in the master control card-reading zone, it can disable or unlock all cards of the room users of corresponding elevator No. And its concrete operation method is: In the mak
14、ing process of mandatory management card, select disabling firstly and then fill in the room number of the user to be disabled at the room number position. Mandatory management card is to prohibit users from using all cards, the selection of enabling is to unlock all cards of corresponding elevator
15、No., in case the cards are unlocked after being disabled, in the making process of mandatory management card, we may select enabling firstly, and then fill in the room number of the user to be enabled at the room number position, make a card and swipe it at the card-reading zone again, then the user can continue to use card. 5. Reporting Function for Lost CardWhen the card is lost, you can make another card with th
