《1253C中英说明书》由会员分享，可在线阅读，更多相关《1253C中英说明书（16页珍藏版）》请在金锄头文库上搜索。
1、精选文库1253C泵控说明书Content目录1. Scope应用场合This specification specifies the Curtis 1253C motor speed controllers which are designed for series pump motors. Its typical applications include the hydraulic systems of material handling vehicles and other industrial vehicles.SHING KO 1253C电机速度控制器是为串励泵控电机而设计的。广泛应
2、用于液压系统的重型 托盘车和其它工业车辆。2. Description 概述1253C offers smooth, silent, cost effective motor speed and torque control according to the signals of lifting, tilt, power steering, sideward move (forward move). They will prolong the life of the motors, contactors, batte ries and reduce maintenances of the sy
3、stems as it greatly reduces high current impact.The output PWM can be programmed with speed select inputs SS1-SS4 and analog throttle input. So the 1253C controllers can ensure not only the lifting speed control but also the system stability and safety. These controllers are fully programmable by me
4、ansof the1311 programmer, with diagnostic and test capability. System status can also beindicatedvia an external LED.The 1253C controllers have completely protection functions such as current limit, reverse polarity protection, startup lockout, over voltage protection, low voltage protection, and so
5、 on. They can provide lift lockout function with Curtis meters (such as 906，803, ENGAGE IV) when battery is deep discharger.CAN communication feature is added to the 1253C, so it can work with other CAN devices such as CAN tiller head which will greatly simplify the wiring.1253C根据上升、下降、转向、前进信号提供了平稳、
6、安静、有效的电机速度和扭矩控 希叽它将延长电机、接触器、电池的使用寿命和减少系统的维护以及大大减小大电流的影响。PWM输出可以通过选择输入SS1-SS4对速度编程，与加速器输入类似。因此 1253C控制器不仅能确保上升速度控制而且保证了系统的稳定和安全。这些控制器都完全可以通过 1311手持编程器编程、诊断和性能测试。系统状态也可以通过外部LED来指示。1253C控制器有完整的保护功能例如限流、反向极性保护、启动锁止、过压保护、欠压保 护等等。它可以使用SHINGKO电量表(例如906、803、ENGAGE IV)提供上升锁止功能当电池 深度放电时。1253C增加了 CAN总线通讯功能，因此它
7、可以与其它CAN总线设备工作，例如CAN总线操纵杆 它将大大简化了接线。3. Encodement命名规则4.1 Model No:1253C - AB_CDWhere1253C :model family型号系列A :Nominal battery voltage额定电池电压424-36V536-48vB:Current rating 额定电流4400A8600ACD :Sequence Number 序列号4.2 P/N: 17726 X YY 部件编号Where17726 :Family number for 1253CX :Product Classification:?Bulk Pa
8、cking5Finished goodsYY:Sequence Number4. Mechanical Specification物理参数4.1.尺寸长(mm )宽(mm )高(mm )195146.077.01) 重量2.30 0.05 kg2) 安装螺丝4*M6孔径尺寸4* 7.2 ( 0.15 ) mm孔间距尺寸133.3 (0.1 ) mmX 130.3 (0)mm4.4. 线路连接Bus BarB+B+ and series pump controller field (S 1)B+和串励泵控控制端（S1 ）BBM-series pump controller (A2)串励泵控制器(
9、A2)Note: (1) The other side of (Al) and the other side of fie Id (S2) should be connected.(2) The dimension of installation hole on Bus Bar is: 8.5 0.13mm, Connect screws: M8 注 意：(1) Al应该和另一端S2连接。(2)安装孔尺寸：8.50.13mm，螺丝：M8Low Current Connector小电流连接Mating connector: Mo lex Mini-Fit Jr. 39012145 with 55
10、56 pin公母接插件：Molex Mini-Fit Jr. 39012145 型插头、5556型端子JI -14Pin1KSI （钥匙开关输入）2POT HIGH电位器高端3POT WIPER电位器中点4POT LOW电位器低端5INTERLOCK互锁6STATUS LED 状态 LED7CAN LOWCAN 低端8SSI9SS210SS3/LOAD HOLD VALVE DRIVERSS3/负载保持阀驱动11SS412LIFT LOCKOUT 上升锁止13CONTACTOR COIL 接触器线圈14CAN HIGH CAN 高端J2 一4Pin1RX数据接收2GND3TX数据发送4+ 12
11、V5. Electrical Specification电气特性5.1. PWM operating frequency:15.6KHzPWN工作频率：15.6KHZ52 Electrical isolation between Bus Bar and heat sink:500V ac (minimum)接线铜条与散热片电气隔离：500Vac(最小值)5.3. KSI input voltage:互锁开关输入电压54 MAX KSI input current (no contactors engaged):最大钥匙开关输入电流(接触器未使用时)：70 mA without programm
12、er; 150 mA with programmer未编程时 70mA,编程时 150mA5.5. logic input voltage逻辑输入电压5.6. Logic input current:逻辑输入电流Sink current: lmA 灌电流：lmA5.7. Status LED driving capability:状态 LED 驱动能力:Sink current: 5mA 灌电流：5mA5.8. Contactor driving capability:接触器驱动能力Sink current: 2A灌电流：2A5.9. Under voltage / Over voltage
13、protection欠压 /过压保护型号欠压 （可编程）过压减小关断过压关断1253C-4xxx16-21 V/24 V2432V/36V1417.5V/24V210265V/36V32V/24V46.5V/36Vcutback voltage is inter-clamped with cutoff voltage 减小电压与关断电压互相影响。5 10. Cuirent Rating 额定电流型号额定电池 电压（伏）电流限制（安培）2分钟电流 （安培）1小时电流 （安培）1253C-440124/36V4004001256. Diagnostics and Troubleshooting诊断
14、与检修Diagnostics 诊断6.l. Programmer Diagnostics编程器诊断The 1311 programmer presents complete diagnostic information in plain language.Faults are displayed in the Faults menu and the status of the controller s inputs/outputs is displayed in the Monitor menu.Accessing the Faults History Menu provides a list
15、 of the faults that have occurred since the diagnostic history was last cleared. Checking (and clearing) the diagnostic history is recommended each time the vehicle is brought for maintenance1311编程器以明了的文字显示所有诊断信息。当前所有故障都在诊断菜单中显示，控制 器输入/输出状态显示在监视菜单中。查看历史故障菜单，会显示上次未被清除的诊断历史故障。在每次维修时应检查并清除 历史故障。1) LED Diagnostics LED 诊断An external Status LED can be connected to the 12
