《BOSON Classroom Labs for CCNA》由会员分享，可在线阅读，更多相关《BOSON Classroom Labs for CCNA（38页珍藏版）》请在金锄头文库上搜索。
1、窗体顶端窗体底端BOSON Classroom Labs for CCNAStudent Lab Guide TABLE OF CONTENTSINTRODUCTION3LAB 1 BASIC ROUTER CONFIGURATION9LAB 2 ADVANCED ROUTER CONFIGURATION14LAB 3 - CDP17LAB 4 TELNET18LAB 5 - TFTP20LAB 6 - RIP22LAB 7 IGRP24LAB 8 EIGRP26LAB 9 - OSPF28LAB 10 CATALYST 1900 SWITCH CONFIGURATION30LAB 11 VL
2、ANs and TRUNKING (Catalyst 1900 Switches)33LAB 12 - CATALYST 2950 SWITCH CONFIGURATION35LAB 13 VLANs and TRUNKING (Catalyst 2950 Switches)38LAB 14 IP ACCESS-LISTS40LAB 15 - NAT/PAT42LAB 16 - PPP & CHAP45LAB 17 ISDN BRI-BRI using Legacy DDR46LAB 18 ISDN BRI-BRI using Dialer Profiles48LAB 19 ISDN PRI
3、using Dialer Profiles50LAB 20 FRAME RELAY52Appendix A - IPX LAB55Appendix B: ANSWERS TO QUESTIONS57Appendix C: LAB CONFIGURATIONS64INTRODUCTIONBoson NetSim: OverviewThe CCNA labs contained in this lab guide are based on the Boson NetSim. This PC-based product simulates a wide variety of Cisco router
4、s as well as the Catalyst 1900, 2950, and 5000 switches. The NetSim supports multiple routing protocols, including RIP, IGRP, EIGRP, and single-area OSPF. It supports different LAN/WAN protocols, including PPP/CHAP, ISDN, and Frame Relay. The exercises in this lab guide only require the NetSim they
5、do not require access to any external router or switch hardware. It should be noted that the NetSim supports many, but not all of the IOS commands available on a real router or switch. All the commands referenced in this lab guide are supported through the Simulator.Getting StartedTo invoke the NetS
6、im, double-click on the Boson NetSim icon on your PC screen. If there is not an icon on the PC screen, you can start the NetSim by pressing Start - Boson NetSim - Boson NetSim. You will be presented with a screen that has buttons at the top representing each router, switch, or PC that you will be co
7、nfiguring. Press one of the buttons to configure a device. Some of the devices are hidden (Switch 3, Switch 4, PC1, and PC2) and can be accessed by pressing the More Devices button. There is also a button that can be pressed to show the network topology that the labs are based on. Lab TopologyThe La
8、b Topology is shown in the diagram on the next page (it can also be viewed by selecting the Topology button at the top of the NetSim screen). You will have:4 x Cisco 2500 routersoeach router has one Ethernet and two serial interfacesoone of the 2500s, router1, has an ISDN BRI interface1 x Cisco 2600
9、 router (identified as router2)ohas one Ethernet interfaceohas both an ISDN BRI and a PRI interface2 x Catalyst 1912 switchesoeach switch has twelve 10baseT and two Fast Ethernet ports2 X Catalyst 2950 switchesoeach switch has twelve 10/100 Ethernet ports2 x PCsThe LAN/WAN interfaces and subnet numb
10、ers are indicated on the diagram. Specific interface IP addresses are included in a table on page 6. LAB TOPOLOGY IP AddressesThe IP addresses and subnet masks used in all the labs are shown in the table below.DEVICEINTERFACEIP ADDRESSMASKrouter1E0160.10.1.1255.255.255.0S0175.10.1.1255.255.255.0S121
11、5.10.1.1255.255.255.0BRI0200.10.1.1255.255.255.0router2F0/0160.10.1.2255.255.255.0BRI0/0200.10.1.2255.255.255.0S0/0 (ISDN PRI)201.10.1.2255.255.255.0router3S0175.10.1.2255.255.255.0S1180.10.1.1255.255.255.0E0197.10.1.1255.255.255.0router4E0195.10.1.1255.255.255.0S0180.10.1.2255.255.255.0router5S0215
12、.10.1.2255.255.255.0switch1-195.10.1.99255.255.255.0switch2- 195.10.1.100255.255.255.0switch3-197.10.1.99255.255.255.0switch4-197.10.1.100255.255.255.0pc1-195.10.1.2255.255.255.0pc2-197.10.1.2255.255.255.0Lab ScenariosThere are 20 labs contained in this Lab Guide. They include:Lab 1 - Basic Router C
13、onfigurationLab 2 - Advanced Router ConfigurationLab 3 - CDPLab 4 - TelnetLab 5 - TFTPLab 6 - RIPLab 7 - IGRPLab 8 - EIGRPLab 9 - OSPFLab 10 Catalyst 1900 Switch ConfigurationLab 11 - VLANs & Trunking (Catalyst 1900)Lab 12 - Catalyst 2950 Switch ConfigurationLab 13 - VLANs and Trunking (Catalyst 295
14、0)Lab 14 - IP Access ListsLab 15 - NAT/PATLab 16 - PPP & CHAPLab 17 - ISDN BRI-BRI using Legacy DDRLab 18 - ISDN BRI-BRI using Dialer ProfilesLab 19 - ISDN PRI using Dialer Profiles Lab 20 - Frame Relay There is also an optional IPX lab contained in Appendix A of this lab guide. These labs build upon each other so the best approach is to follow the labs sequentially. You will also be asked questions at various points during the lab. Answers to these questions are contained in Appendix B at the back of this lab guide. Appendix
