《CMW500-CDMA终端测试步骤-(精)》由会员分享，可在线阅读，更多相关《CMW500-CDMA终端测试步骤-(精)（24页珍藏版）》请在金锄头文库上搜索。
1、CMW500 CDMA终端射频测试环节接受机测试项目:3.4Forward Traffic Channel Demodulation Performance3.5.1Receiver Sensitivity and Dynamic Range发射机测试项目：4.3.1Time Reference4.3.2Reverse Pilot Channel to Code Channel Time Tolerance4.3.3Reverse Pilot Channel to Code Channel Phase Tolerance4.3.4Waveform Quality and Frequency A
2、ccuracy4.3.5Code Domain Power4.4.1Range of Open Loop Output Power4.4.2Time Response of Open Loop Power Control4.4.4Range of Closed Loop Power Control4.4.5Maximum RF Output Power4.4.6Minimum Controlled Output Power4.4.7Standby Output Power and Gated Output Power4.4.9Code Channel to Reverse Pilot Chan
3、nel Output Power Accuracy4.5.1Conducted Spurious Emissions发射机测试：4.3.1 Time Reference测试环节：In signalling:Config _ System _ Physical Layer _Service Option SO2(LoopbackConfig _ System _ Physical Layer _Radio Configuration 1/1 (当以RC1建立时，为O-QPSK 调制 或者Config _ System _ Physical Layer _Radio Configuration 3
4、/3 (当以RC3建立时，为H-PSK 调制 In measurement:Config _Trigger _Trigger Source _Super Frame读取其测量成果:Task _CDMA TX measurement _Multi Evaluation _Display _Select View _ Error Vector Magnitude测试成果： 规范指标：在稳态条件下移动台时间基准应在移动台天线连接器处测量在被用于解调的最早达到多径成分浮现时间的1s 范畴内。4.3.2 Reverse Pilot Channel to Code Channel Time Toleran
5、ce测试环节：In signalling:Config _ System _ Physical Layer _Service Option SO2(Loopback Config _ System _ Physical Layer _Radio Configuration 3/3手机进入连接状态:读取其测量成果:In measurement:Task _CDMA TX measurement _Multi Evaluation _Display _ Select View _ Channel Time Offset 规范指标：当工作在无线配备3至6时反向导频信道和所有其他共享相似反向CDMA
6、信道的码分信道间的时间误差应不不小于10ns 。4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance测试环节：In signalling:Config _ System _ Physical Layer _Service Option SO2(LoopbackConfig _ System _ Physical Layer _Radio Configuration 3/3手机进入连接状态:读取其测量成果:In measurement:Task _CDMA TX measurement _Multi Evaluation _Dis
7、play _ Select View _ 规范指标：反向导频信道和所有其他共享相似反向CDMA 信道的码分信道间的相位差不应超过0.15弧度也不适宜超过0.05弧度。4.3.4 Waveform Quality and Frequency Accuracy测试环节：In signalling: Config _ System _ Physical Layer _Service Option SO2(LoopbackConfig _ System _ Physical Layer _Radio Configuration 1/1 (当以RC1建立时，为O-QPSK 调制 或者Config _ S
8、ystem _ Physical Layer _Radio Configuration 3/3 (当以RC3建立时，为H-PSK 调制确认手机已经进入连接状态：Config _ System _ RF Power _CDMA Power -75.00 dBm读取其测量成果:Task _CDMA TX measurement _Multi Evaluation _Display _Select View _ PowerTask _CDMA TX measurement _Multi Evaluation _Display _Select View _ Error Vector Magnitude
9、测试成果： 规范指标：波形质量因数应不小于0.944过剩功率不不小于0.25dB 载波频率误差f 在频段类别02357和9时应在300Hz 范畴内在频段类别146和8时应在150Hz 范畴内发射时间误差应在1s 范畴内。4.3.5 Code Domain Power测试环节：In signalling: Config _ System _ Physical Layer _Service Option SO2(LoopbackConfig _ System _ Physical Layer _Radio Configuration 3/3 （只对H-PSK ）确认手机已经进入连接状态：Confi
10、g _ System _RF Power _CDMA Power -101.00 dBmConfig _ System _ Physical Layer _Code Channels _PICH -7.00 dBConfig _ System _ Physical Layer _Code Channels _FCH -7.40 dB读取其测量成果:Task _CDMA TX measurement _Multi Evaluation _Display _Select View _ Code Domain Power测试成果： 规范指标：每个未激活码分信道的码域功率应比组合的I 和Q 数据信道上
11、测量的总输出功率至少低23dB 。4.4.1 Range of Open Loop Output Power测试环节：In signalling:按照下表设立网络参数：Config _ System _RF Power _AWGN Level OffConfig _ System _ Network _Access Probes _Open Loop Adjust 打开社区，设立好需要的频段和信道，按照下图所示分别设立Test 1,2,3的前向功率：Config _ System _RF Power _CDMA Power Config _ System _ Network _Access P
12、robes _ Access Probes Mode Ignore关闭社区。Config _ System _ Network _Access Probes _Probe Increment 0 dB打开GPRF measurement:Config _Scenario Combined Signal PathConfig _Measurement Control _Repetition _SingleShotConfig _Measurement Control _Statistic Count 3Config _Measurement Control _Step Length 10 msC
13、onfig _Measurement Control _Measurement Length 10 msConfig _Trigger _Minimum Trigger Gap 10 ms如果想测宽带功率，如下设立滤波器类型和带宽：Config _Measurement Control _Filter _Filter Type BandpassConfig _Measurement Control _Filter _Bandpass Filter 9 MHz如果想测CDMA 信号带宽内的功率，如下设立滤波器：Config _Measurement Control _Filter _Filter
14、 Type CDMAConfig _Trigger _Trigger Source IF PowerConfig _Trigger _Trigger Slope Rising EgdeConfig _Trigger _Trigger Threshold -30 dBConfig _Trigger _Trigger Offset 100 sConfig _Trigger _Trigger Timeout 60 sConfig _Trigger _Trigger Mode Retrigger all打开社区，打开GPRF 测试，再打开DUT 电源等待测试成果。测试成果： 规范指标：参照规范3GPP
15、2 C. S0011-A，根据下表判断与否符合规范。 4.4.2 Time Response of Open Loop Power Control暂不支持。4.4.4 Range of Closed Loop Power Control测试环节：In signalling: Config _ System _ Physical Layer _Service Option SO2(LoopbackConfig _ System _ Physical Layer _Radio Configuration 1/1 (当以RC1建立时 或者Config _ System _ Physical Layer _Radio Configuration 3/3 (当以RC3建立时 确认手机已经进入连接状态，读取一次测量成果，记为P0:Task _CDMA TX measurement _Multi Evaluation _Display _Select View _ Power 然后：Config _ System _Reverse Power Control _Power control Bits All up读取一次测量成果，记为P1:Task _CDMA TX m
