《机电一体化毕业设计(论文)车床的PLC控制设计》由会员分享,可在线阅读,更多相关《机电一体化毕业设计(论文)车床的PLC控制设计(30页珍藏版)》请在金锄头文库上搜索。
1、车床的PLC控制设计The lathe PLC control desig专 业:08机电一体化大专班 学 生 姓 名: 学 号: 指 导 教 师: 完 成 日 期: 武威职业学院工程技术系车床的PLC控制设计摘 要传统的C650车床采用继电器实现电气控制,接线多且复杂,体积大,功耗大,一旦系统构成,想改变或增加功能很困难,其工作性能已不能达到现代生产的要求。因此,以PLC取代常规的继电器,可提高工作性能,并且达到车床的控制要求。本次设计介绍了C650卧式车床电气控制系统的工作原理及其运动形式,编写了PLC控制梯形图程序和指令表程序。利用PLC控制系统,实现了车床启动、正转反转、反接制动、刀架
2、快速移动、冷却泵在作等一些列功能,改由PLC控制后,其控制系统大大的简单化,并且维修方便,易于检查,节省大量的继电器元件,机床的各项性能有了很大的改善,工作效率有了明显提高。经反复调试,该项技术可推广应用于自动化其他领域的控制系统中,系统运行情况良好,车削精度更高。关键词:PLC;车床;继电器 - I - 车床的PLC控制设计ABSTRACTThe traditional C650 lathe adopts relays electrical control realization .Wiring and complex, big volume and power consumption .O
3、nce composition the systems, it is very difficult to change or add function. Its performance cannot reach the requirement of modern production. Therefore, replace relay of conventional PLC, it is can improve the working performance and achieve the lathe control requirements.This design recommends C6
4、50 horizontal lathes are introduced the working principle of electric control system and the forms of exercise. Write a PLC control procedures and instructions ladder-diagram form program. Using PLC control system, realized the lathe, are turning inversion, reverse connect braking, cutter in fast mo
5、ving, cooling pump and some function. By PLC control, the control system of large and convenient maintenance, simple, easy to check and save a lot of relays, various properties of machine elements have greatly improved, work efficiency was obviously improved.After repeated testing, the technology ca
6、n be applied to other areas of automation control system, the system operation condition, turning a higher preKey words:PLC; lathe;Relay- III -目 录摘要. .IABSTRACT. .II1 前言.11.1 C650型卧式车床简介.21.2 PLC在电气控制系统中的应用.31.3C650型卧式车床发展趋势.42 系统总设计.42.1PLC控制系统的设计基本内容.52.2PLC控制系统设计原则.53 系统硬件设计.53.1主要电气的选择. 53.1.1交流接触器和中间继电器的选择.63.1.2保护电器的选择.63.1.3控制器的选择.73.2 C650卧式车床的主要结构和运动形式.73.3 C650卧式车床控制原理电路图概述及原理分析.83.4I/O地址的分配.113.5I/O接线图.124 系统软件设计.134.1 PLC的系统结构和基本工作原理.134.2 PLC的基本功能和基本指令.144.21 PLC基本功能.144.22 PLC基本指令.154.3 PLC控制梯形图.165 系统调试.175.1硬件检查.175.2系统综合调试.18结论.19致谢.20参考文献.21附录.