《CombineUserGuide(new)船舶M站操作手册》由会员分享，可在线阅读，更多相关《CombineUserGuide(new)船舶M站操作手册（44页珍藏版）》请在金锄头文库上搜索。
1、2 / 44AMOSConnect(7.4.27) Quick User Guide (English Version)Table of ContentChapter 1 Connection between Inmarsat and PC. Page3Chapter 2 - AMOSConnect Quick Installation. Page 42.1 Verify Connection Page 5Chapter 3 AMOSConnect simple user guide. Page 73.1 Start AMOS Connect Page 73.2 Editing address
2、 books Page 73.3 Compose new email Page 103.4 Compose FAX (Text Only) Page 143.5 Compose FAX (Attachment) Page 163.6 - Compose Telex Page 183.7 Dial and connect Page 203.8 Check connection status Page 22Chapter 4 FAQ Session. Page 23Appendix I . Page 36Important Note:After install AmosConnect, pleas
3、e make sure you backup the folder C:AM32AMPO (or C:AMPO) at least once per month, so you could recovery all your AmosConnect setting and history in case you PC have technical problemHow to Backup AmosConnect and Reinstall in New PC 1. Copy the folder C:AM32AMPO ( the mail path folder could be found
4、in Help/about AmosConnect) at least once per month to other PC or Hard Disk2. If PC with AmosConnect have problem, copy the AMPO folder to the new pc 3. Install AmosConnect version 7.4 by click AC-7.4.16 (Setup.exe) from you AmosConnect CD , the Setup.exe is in the source folder , dont use setup.bat
5、 unless you want to install new database 4. After installation , click “Connect to existing post office” 5. Chose Local Database and browse to the folder of AMPO 6. In C:Am32, or C:program fileAmosConnect, find out file “ ResetDeviceComputer.exe “ and double click it ( to reset the modem driver) 7.
6、Your AmosConnect should be fully recovered Chapter 1 Connection between Inmarsat and PCInmarsat B:Computer(9 Pin COM Port)Inmarsat B Terminal(DTE Port)Computer(9 Pin COM Port)(9 Pin or 25 pin )Inmarsat Mini-M:Mini-M Terminal(9 Pin Data Port)Computer(9 Pin COM Port)Computer(9 Pin COM Port)Inmarsat F
7、(RS232 Direct Connection):Inmarsat-F Terminal(RS232 Port)Computer(9 Pin COM Port)RS232 Serial FAX MachineTelephoneInmarsat F( With ISDN TA):ISDN TAInmarsat-F Terminal(ISDN Port)Computer(9 Pin COM Port)ISDN LineSerial LineFAX MachineTelephoneChapter 2- AMOSConnect Quick installation1. Place AMOSConne
8、ct CD in the CDROM drive2. Double click to open ”My Computer” on desktop3. Double click on CD-ROM drive 4. Double click “Setup”, a window will pop up, keep waiting during the installation until you see the message AMOS-Mail restored. Please try to run AMOS Connect and confirm 5. After installation h
9、as been completed, the window will close automatically.6. For Re-Installation, follows these steps :a) Remove “AMOS Connect” under “Add/Remove Programs” in “Control Panel” b) Delete the whole directory C:am32 c) Start installation from step 12.1 Verify Connection1. Double the icon AMOS Connect on de
10、sktop2. Click the Dail button, follow by the ”Connect” button3. If no error message pop up and you can see statistics count , that means the connection is in progress. Now, you can start to use AMOS Connect.4. If error message pop up or you cannot make a connection, please refer to Chapter 4 FAQ Ses
11、sion for troubleshoot for troubleshootChapter 3 AMOSConnect simple user guide3.1 Start AMOS Connect1. Double click the icon AMOS Connect on desktop3.2 Editing Address Books (E-mail, Fax and Telex Service)2. Click the Address button, the Address Book window will pop up3. Click the New button, the New
12、 Directory will pop up4. Adding contacts in Address Book :a. Adding Email address:i. Select Internet in the Template pull-down menuii. Input the email address in the Address. (e.g. The Email address is as shown in the following example)b. Adding FAX number:i. Select Fax” in the Template pull-down m
13、enuii. Input the fax number in the Address. (e.g. The fax number is + as shown in the following example)c. Adding telex number:i. Select Telex in the Template pull-down menuii. Input the telex number in the Address. (e.g. The telex number is + as shown in the following example.)3.3 Compose new email
14、1. Click the New icon at top-left hand corn, the New Message and Address Selection windows will pop up2. Click to select the recipient, click To, Cc or Bcc to put it on the list3. Click Close when finish4. Enter the subject and content for the email5. Click Attach button if you want to add attachment, the Add Attachment(s) window will pop up6. Find and click on the target file, click open
