《330特技飞机打印图纸》由会员分享，可在线阅读，更多相关《330特技飞机打印图纸（1页珍藏版）》请在金锄头文库上搜索。
1、TapeBest results are achieved by using 1”wide Du-Bro RC Electric Flyer Hinge Tape(3M Blenderm)for all hinges.Clean all parts with rubbing alcohol before applying.All airframe parts and control surfaces are cut from Deporn FoamDashed line repre-sents alternative cut line if 6mm side plate xBrace is u
2、sedDesign by Mickey Crawley-Plans by Steven Gibson Copyright 2005 3D.All rights reserved.rev-1.0305Wing Span.36”Length.34.5”Weight.12-13ozPower.AXI 2212/34 Prop.GWS 12x4Ch.4Battery.3 Cell-700 to 1350mAh-Li-Poly*Depron 6mm/3mm White()*Carbon Fiber Tube.157(3.9mm)x 30(wing tube)*.040 Solid Carbon Rod(
3、push rods+stab support)or.optional 3mm flat carbon rod tab support*.080 Solid Carbon Rod(landing gear support)*Medium or Thick foam friendly CA*Foam friendly CA accelerator*JZ Products Super RC“Z 56 glue*1”Self-sticking Hook&Loop (Velcro-Industrial Strength)tape*Clear packing tape*4-E-flite Micro Co
4、ntrol Horns No.EFLA200 OR.4 Du-Bro Micro Control Horns No.848*4 Du-Bro Micro E/Z Links No.849*.032 wire control arms*Du-Bro RC Electric Flyer Hinge Tape(3M Blenderm)*Zagi tape for trim scheme(optional)*Straight edge razor-blades*No.11 Xacto knife*Metal yardstick*3M Photomount Spray Adhesive (for pla
5、n transfer to Depron)Rx and Servos*GWS R-4PH 4ch receiver or equivalent*4 Waypoint W-084 Micro Servos or Hitec HS 55Brushless Motor*AXI 2212/34 outrunner(Max 3D performance)Speed Controller*Phoenix 25amp speed controllerBattery*3 Cell 700-1350mAh-11.1v Li-PolyProp(s)*GWS 12x6 Slow Flyer*APC 12x3.8 e
6、lectric slow flyerLightly coat back of plan parts with Spray Adhesive,apply each part to Depron.Carefully cut each part outusing a straightedge and#11 Xacto.Speed control,Rx and rudder/elevator servos.Note landing gear set-upA Rotary Tool Cutting Adapter is perfect for clean easy to make grooves for
7、 Fiber Carbon rod stiffeners.FLIGHT SYSTEM RECOMMENDATIONSMATERIALS LISTHINGE DETAILPUSHROD DETAILBUILDING&FINISHING DETIALSEXTRA 330-3 D PARK FLYER SPECS6mm Depron reinforcer.Glue to bottom of the x-brace behind the trailing edge of wing.Landing Gear3mm DepronDenotes cut-linesAXI 2212/34 External R
8、otor Brushless AXI Brushless Motor Shown 1/8”light plywood radial mount,reinforced with Depron triangle stockon all 4 sidesRudder ServoAileron ServoCut side plate(xBrace)from 3mm Depron6mm DepronoptionalElevator ServoServo cutoutServo cutout.8mm carbon rod landing gear support/stiffener.Groove foam
9、and glue with order-free(foam friendly)CA or JZ Products Super RC Z 56Glue scrape Depron triangles for extra strengthWingNOTE:landing gear shown is not functional but is recommended for improved flight performance 3 Cell700-1350 mAh Li-Poly BatteryAll parts are cut from 6mm Depron unless stated othe
10、rwise012341230Inch Scale reference,check after printing.Extra 330-3D Park Flyer.032 wire control rods.040 Solid Carbon Rod push rodsHeat shrink tubingColored Zagi tape works great for trim.Its best to trim each part before assembly.Not speed control and Rx locations.Battery is on the opposite side.N
11、onfunctional landing gear setup.Adds to the overall flight characteristics.Carbon Fiber Tube.157(3.9mm).Cut a channel(per plan)on the bottom of the wing only and CA or RC-56 in place.Wing cut from one piece of 6mm Depron foamAileron control hornsAileron cut lineCGInitial CG 2-2.5”from leading edge rootReinforce carbon rod landing gear crossing with 1/32 ply Use on control servo arms.CA 3”of wire to 2mm carbon fiber rod,secure with 1”of heat shrinking tubing.Carbon rod fits opposite side of control arms,wire connects and holds rod in place
