《ORACLE SUN 存储阵列ZFS 7320安装配置手册》由会员分享，可在线阅读，更多相关《ORACLE SUN 存储阵列ZFS 7320安装配置手册（16页珍藏版）》请在金锄头文库上搜索。
1、SUN 7320安装配置文档一：设置7320机头7320是一个存储机头，他本身有系统，不需要安装，（1） 用串口线连串口，波特率设为9600（2） 给机器加电，机器在加电自检完成后会让登录ilom控制台（3） ilom控制台的默认账号为root，密码为changemeORACLESP-1144FMM0HY login: rootPassword: Oracle(R) Integrated Lights Out ManagerVersion 3.0.14.11 r61398Copyright (c) 2010, Oracle and/or its affiliates. All rights r
2、eserved.Warning: password is set to factory default.- cd /SP/network（转到网络管理目录） /SP/network- show /SP/network（显示当前的网络管理口的IP，新的机器都是0，需要设置） /SP/network Targets: interconnect ipv6 test Properties: commitpending = (Cannot show property) dhcp_server_ip = none ipaddress = 0.0.0.0 ipdiscovery = dhcp ipgatew
3、ay = 0.0.0.0 ipnetmask = 0.0.0.0 macaddress = 00:21:28:E8:36:3E managementport = /SYS/SP/NET0 outofbandmacaddress = 00:21:28:E8:36:3E pendingipaddress = 0.0.0.0 pendingipdiscovery = dhcp pendingipgateway = 0.0.0.0 pendingipnetmask = 0.0.0.0 pendingmanagementport = /SYS/SP/NET0 sidebandmacaddress = 0
4、0:21:28:E8:36:3F state = enabled Commands: cd set show- set pendingipaddress=192.168.200.205 （设置管理口IP）Set pendingipaddress to 192.168.200.205- set pendingipgateway=192.168.200.1 （子网掩码）Set pendingipgateway to 192.168.200.1- set pendingipnetmask=255.255.255.0 （网关）Set pendingipnetmask to 255.255.255.0-
5、 set commitpending=true （提交设置）Set commitpending to true- show /SP/network Targets: interconnect ipv6 test Properties: commitpending = (Cannot show property) dhcp_server_ip = none ipaddress = 192.168.200.205 ipdiscovery = static ipgateway = 192.168.200.1 ipnetmask = 255.255.255.0 macaddress = 00:21:2
6、8:E8:36:3E managementport = /SYS/SP/NET0 outofbandmacaddress = 00:21:28:E8:36:3E pendingipaddress = 192.168.200.205 pendingipdiscovery = static pendingipgateway = 192.168.200.1 pendingipnetmask = 255.255.255.0 pendingmanagementport = /SYS/SP/NET0 sidebandmacaddress = 00:21:28:E8:36:3F state = enable
7、d Commands: cd set show- start SYS（启动系统）Are you sure you want to start /SYS (y/n)? ystart: Target already starte- start /SP/consoleAre you sure you want to start /SP/console (y/n)? ySerial console started. To stop, type ESC (Press any key to begin configuring appliance: *（按任意键进入配置界面）Hit any key to c
8、ontinue to the initial configuration screen:Sun Storage 7320 ConfigurationCopyright 2010 Sun Microsystems, Inc. All rights reserved.NET-0 NET-1 NET-2 NET-3 （“=”是网口联通，“x”是网口断开）Host Name: 7320c（主机名，自己决定）DNS Domain: （DNS域，没有的话就随便添一个）IP Address: 202.118.82.77 （对外服务口的IP）IP Netmask: 255.255.252.192（子网掩码）D
9、efault Router: 202.118.82.65（网关）* Password: （设置密码root）* Re-enter Password:Please enter the required (*) configuration dataESC-1: Done ESC-2: Help ESC-3: Halt ESC-4: Reboot ESC-5: InfoSun ZFS Storage 7320 ConfigurationCopyright 2011 Oracle All rights reserved.Your new appliance is now ready for confi
10、guration. To configure yourappliance, use a web browser to visit the following link: https:/7320c.localdomain:215/If your network administrator has not yet assigned the network name you chosefor the appliance, you can also configure your appliance using the link: https:/202.118.82.77:215/If you are
11、unable to connect to the appliance through your web browser, youcan begin text-mode configuration by logging in as root and entering theadministrator password you specified on the previous screen.For help, see 二：配置双机打开IE浏览器，输入 https:/202.118.82.77:215/输入账号（root）密码（root）点击start点击cluster配置双机以为双机间的线已经连
12、接好，所以只需要点一下另一台机器的主机名（7320d）并设置密码（root）（另一台机器不需要像上面那么配置）配置完成确认网络资源配置dns（没有dns所以不需要配置）配置时间和ntp服务(没有NTP serve 所以不需要配置)配置名称服务和目录服务（不需要）配置存储池（后面手工配置，这里不选）三：配置存储资源这个是查看7320整体状态的页面点击configuration -storage 配置存储，点击Available Pools旁边的 + 号添加存储池这个页面就会显示可用的存储空间，这次存储挂了3个磁盘柜，每个柜24块，应用需要大概20T左右的空间，所以就选择前两个磁盘柜，最后一个柜磁
13、盘数改成0就可以。选择raid策略，这和普通的raid 0,1,5 不太一样，点击不同的profile 下面都会详细的介绍，这次我们选第一个profile 双校验，这样raid就做好了。下面需要切分raid做卷，点击Shares - SHARES -LUNs，点击 + 号。填上卷名字，指定卷大小2000G总共10个卷，前9个每个2000G，最后一个1600G分配卷，点击configuration SAN，把两个光纤口从initiator改成target点击configuration SAN -initiators ，点击 Fibre Channel Initiators旁边的 + 号。 下边有识别到的主机的wwn号，点击然后起个名字。点击左边做好的 Fibre Channel Initiators，把它拖到右边Fibre Channel Initiator Group里面新建一个组，如图我们把2台M5000的4个光纤口加到initiators- 0里面。点击Shares选择做好的卷，点击 protocols，把Initiator Group改成建好的initiat
