《流體輔助射出成形充填流動可視化分析與探討》由会员分享，可在线阅读，更多相关《流體輔助射出成形充填流動可視化分析與探討（3页珍藏版）》请在金锄头文库上搜索。
1、中文題目：標楷體14級字型，粗體；文字置中版面設定： 邊界上2.5cm冠痂赢成形充填流動可視化分析與侖亠英文題目：Time New Roman 14 級字型， 粗體；文了置中Flow Visualization of the Fluid Assisted Injection Molding Processk中文作者姓名：f碗文作者姓名：J住楷體12級字型；文字置中/吳逸群1劉士榮2 一一Time New Roman 12 級字型； 字置中zYi-Chuan Wu, Shih-Jung Liu標楷體12級字型；文字置中|科盛科技 Core Tech System Co., Ltd$長庚大學機械系
2、教授 Department of Mechanical Engineering, Chang Gung University中文摘要標題：_標梢體12級字型，粗體；摘 要乜字置中丿文服務單位:Time New Roman 12 級字型； 、文字置中近本研究主要係對高分子液體輔助射出成型件(Water Assisted Injection Molding )之充填過程做可視化(Flow visu汕zdtion)之研究與探討，用以察融膠與水在射出成形過程中之交互現象與充填行為。研究將運用先前由本實驗室自行開發之小型研究用液體輔助系統包括水壓幫浦、壓力控制、程序控制及水針等，及開發一新型可視化射出成
3、形模 具及不同幾何形狀模穴模仁包括平板、板厚不同、對稱肋件與補強肋件等四種幾何形狀 模具。而研究的問題將包括水壓、水溫、模溫、熔膠溫度、延遲時間等之影響。研究亦將探討不同幾何形狀之影響，此外研究也將同時探討不同高分子材料之流變特性與整體加工之關係與探討溫度與壓力的動態變化。KI繼詞：严豐型，液體輔助，革新性射出 中文關鍵詞：標楷體12級字型；標題加粗；文字Abstract靠左對齊；4組6組關鍵字英文摘要標題：Time New Roman 12 級字型； 體；文字iK中This report is devoted to studying the filling phenomena文扌商要:mol
4、dings by using a dynamic visualization technique Experiments Time New Roman 12 級字型；80-ton injection-molding machine equipped with gas and water文字靠左對齊版面設定: 邊界左2cm版面設定: 邊界右2cmmateria used was semi-crystalline polypropylene material A flow visualization mold was specially designed and made for this stu
5、dy A high-speed video camera was used to record the mold filling phenomena of rectangular cavities with different channel geometry and layouts: a flat plate, a plate with two zones of different depths, a plate with symmetric ribs, and a plate with fishbone ribs. The interaction between the assisting
6、 media and the polymer melt during molding was observed, and insight into the penetration behaviors of the fluid was summarized. In addition, comparisons have been made between the mold-filling process by gas assisted injection molding and water assisted injection molding.Keyword： injection molding, water assisted,版面設定： 邊界下3cm英文關鍵詞：Time New Roman 12級字型；標題加 粗；文字靠左對齊；4組6組關鍵字
